Skip to content

12 Volt Heated Towel Rails

0 Items

Whoops, there are none available in your area

View all products

12V heated towel rails buying guide

A 12V heated towel rail runs from a transformer that steps mains power down to 12 volts, and it is hardwired by an electrician. For most bathrooms the right call is a 12V rail when it has to sit close to water, such as beside a shower, because a 12V rail can go anywhere in the bathroom, including Zone 1. Otherwise a 240V rail is simpler to fit. This guide sets out how 12V rails work, where the transformer goes and which rails are in this collection.

What 12V means

The only technical difference between a 12V and a 240V rail is the voltage that reaches the rail. A 12V rail is wired into a transformer, which reduces the mains voltage from 240V to 12V. The transformer connects to the mains, so a 12V rail is a mains-powered rail. Low voltage is not low wattage. A 12V rail and a 240V rail of the same size and wattage give off the same heat, because heat output is set by wattage, not by voltage.

Where 12V rails can go

A 12V rail can go anywhere in the bathroom, including the shower area, as long as the transformer and any timer or switch are placed correctly for their IP rating. That is the reason to choose 12V: where the rail sits close to water, a 12V model is the right choice. A 240V rail is limited to certain zones by its IP rating, and most 240V Thermorail rails are IP55 and need to be at least 600mm from a water source or spout. Use a 240V rail outside Zone 1 where you can, and a 12V rail if the rail must sit in Zone 1. Confirm the position with your electrician.

The transformer

  • The transformer must sit outside Zone 2, within 2 metres of the rail, with adequate access and ventilation.
  • 12V rails can only be hardwired. The electrician wires the rail to the transformer.
  • Phoenix, Thermogroup, Nero and Fienza rails in this collection come with a transformer. The Caroma 12V rails are sold without one: the matching 12V 72W transformer is a separate item, and one serves one to three rails.

Plan the transformer position before the wall is lined, because it needs to be reachable and ventilated.

The 12V rails in this collection

Brand and rail Size Power and rating Transformer and wiring
Phoenix round and square rails 600mm and 800mm; 800mm round is 38mm by 870mm by 82mm 35 watts, IPX5 Transformer included, integrated switch, cable through the bottom mount, hardwired by a licensed electrician, 1.3 metre lead
Phoenix triple rails 600mm and 800mm, round and square 35 watts per rail, IPX5 Three rails in the box with the transformer
Thermogroup 12V ladder, round 600mm by 800mm by 122mm, 7 bars 90 watts, IP55 Concealed wiring on any of the four legs
Thermogroup 12V 4 Bar ladder 550mm wide 65 to 70 watts, IP55 Transformer supplied, wiring point left and right, hardwired only
Thermogroup 12V singles Vertical 900mm; horizontal 450mm, 632mm and 832mm 14 to 30 watts, IP45 to IP55 Transformer in the box, concealed wiring
Caroma Liano II and Urbane II Verticals 900mm and 1000mm; horizontals 640mm 12 to 20 watts, IP55 Transformer sold separately, hardwired by a licensed electrician
Fienza Empire Slim 40mm by 900mm, 60mm deep 25 watts, IP55 Concealed wiring, top or bottom
Nero vertical rail 142mm by 900mm, 100mm deep 30 watts, IP55 Transformer and hook included, integrated switch

Ladder or single bar

A ladder gives a towel more contact with the heated bars than a single bar does, so it dries and warms a towel better. The heated towel ladders collection holds the 12V ladders alongside the 240V ones. A vertical or horizontal bar is one heated bar, so use one bar per towel, and fit two or three side by side if more towels hang at once. The vertical heated towel rails and horizontal heated towel rails collections hold the single bars.

The Phoenix rails mount vertically or horizontally, and a matching hook lets one vertical rail carry two towels. The Thermogroup 12V singles are designed to be installed in sets, and a minimum of three gives enough heated surface for towels to dry.

240V or 12V

12V rail 240V rail
Power Wired to a transformer, which steps 240V down to 12V Wired straight to 240V mains, no transformer
Wiring Hardwired only Most can be hardwired or plugged in
Position Anywhere in the bathroom, including Zone 1 Limited by IP rating; most Thermorail 240V rails need 600mm from a water source
Heat Set by wattage Set by wattage

Can a 12V rail run in a caravan or from a battery?

The 12V rails here are made to run from a mains transformer, which steps mains power from 240V to 12V. For a battery or vehicle supply, ask an electrician before you order.

12V vertical and single bars compared

Rail Size Output Rating
Thermogroup straight round vertical 142mm by 900mm, 100mm deep 22 to 30 watts IP55
Thermogroup flat pill vertical 50mm by 900mm, 50mm deep 20 to 25 watts IP55
Thermogroup round triple tube vertical 75mm by 900mm, 100mm deep 27 watts IP55
Thermogroup round single, horizontal 632mm by 32mm, 100mm deep 18 watts IP45
Thermogroup square single, horizontal 632mm by 40mm, 100mm deep 23 watts IP45
Caroma Liano II vertical 104mm by 900mm, 75mm deep 20 watts IP55
Caroma Urbane II vertical 40mm by 1000mm, 60mm deep 16.5 watts IP55
Caroma Liano II horizontal 640mm by 32mm, 75mm deep 12 watts IP55
Fienza Empire Slim vertical 40mm by 900mm, 60mm deep 25 watts IP55
Nero vertical 142mm by 900mm, 100mm deep 30 watts IP55

How hot a 12V rail gets

The Thermogroup 12V 4 Bar ladder is designed to heat up quickly and reach around 45 to 55 degrees. A vertical Thermorail heats to around 35 degrees, and a towel placed over the bars insulates the rail and lifts the temperature under the towel to between 50 and 55 degrees. A vertical rail has less surface contact than a ladder, so it dries a towel less well. The Caroma rails run at 40 degrees, give or take 5, in a 22 degree room. That is enough to dry a towel and keep it warm. It does not heat the room, so a bathroom that needs warm air also needs a ceiling heater or underfloor heating, which the bathroom heating and ventilation collection covers.

Planning the transformer

  1. Count the 12V rails and check which brand each is: Phoenix, Thermogroup, Nero and Fienza rails come with a transformer, and Caroma rails need one bought separately.
  2. Choose a position outside Zone 2 and within 2 metres of the rail, with access for service and ventilation around it.
  3. Confirm any timer or switch sits in the zone that suits its IP rating.
  4. Have a licensed electrician wire the rail to the transformer and the transformer to the mains.

12V ladders

The Thermogroup 12V round ladder is 600mm wide and 800mm high, with 7 bars at 90 watts. It has concealed wiring only, and the wiring is possible on all four legs, which gives a neat finish. The 12V 4 Bar ladder is 550mm wide, comes in polished and brushed stainless steel, and has a wiring point on both the left and right sides, with wiring at the top or the bottom of the rail. Both can be installed close to a wet area and anywhere in the bathroom, including Zone 1. They need a transformer, and the 4 Bar can only be hardwired.

The Phoenix rails suit compact bathrooms. They are 600mm or 800mm long, mount vertically or horizontally, and hold a towel or a robe. The triple versions put three rails in the box, which is the easiest way to build a stacked ladder look from one purchase.

What a 12V rail uses

Divide the rail's wattage by 1,000, then multiply by the hours it runs. A 12 watt Caroma horizontal bar running six hours a day uses 0.07 kilowatt-hours. A 35 watt Phoenix rail uses 0.21, and a 90 watt Thermogroup ladder uses 0.54. A set of three 35 watt Phoenix rails uses 0.63 over six hours. A rail should not run constantly, because heat builds up under the towel, and a timer keeps the running hours to the ones that count. The controllers and thermostats and Thermogroup timers and thermostats collections hold timers that match the rail. Phoenix and Nero rails have an integrated switch on the rail.

Choosing the finish

Choose the finish to match the tapware in the room. The 12V rails come in chrome, brushed nickel, black, gunmetal, brass and gold, white, bronze and stainless steel.

Sizing and fit

Measure the wall before the rail. Overall size is the footprint on the wall, and the fixing distance is the distance between the mounts, and the two are different numbers. Set out the holes from the fixing distance, and leave clear wall above and below the rail so air moves around the towels. Have a licensed electrician connect the rail and the transformer.

Care

Clean the rail with a soft cloth and a non-abrasive cleaner, because harsh scrubbing and acid cleaners mark the surface. A rail is hot to the touch, so supervise young children near it.

Where to go next

The heated towel rails collection compares every brand, finish and voltage together.

Frequently Asked Questions

What does "12-volt heated towel rail" actually mean?

It refers to the rail's electrical operating voltage rather than its finish or style. A 12-volt (or more broadly, low-voltage) heated towel rail runs its heating element at a much lower voltage than Australia's standard 240V mains supply, stepped down through a transformer, rather than the rail itself being wired directly to full mains voltage. This is a different distinction to finish options like brass or nickel, which describe appearance, not how the rail is powered.

Do heated towel rails need to be hardwired?

Not necessarily. A standard mains-voltage electric towel rail can be either hardwired directly into the electrical circuit or supplied with a plug for a standard power point, depending on the model. A 12-volt or low-voltage rail typically runs off a plug-in or hardwired transformer that steps mains power down before it reaches the rail itself. Always check the specific installation method listed for the model you're considering rather than assuming.

Is a 12-volt heated towel rail safer for bathroom installation?

Low-voltage systems are often chosen for locations closer to water because the rail itself operates at a much lower voltage than the mains supply, which is one reason some product classes at 12V can be positioned within a bathroom's designated wet zones with fewer restrictions than a mains-voltage unit. That said, Australian electrical safety rules for bathroom wet zones are specific and vary depending on the exact product and installation method, so always confirm local requirements and get a licensed electrician to check placement and wiring before installation, even for a low-voltage product.

Can I install a 12-volt heated towel rail myself?

Some plug-in, transformer-based low-voltage products can be installed without an electrician, but any work involving fixed wiring, a transformer connected to the mains circuit, or installation within a bathroom's wet zone should be carried out or at minimum checked by a licensed electrician. Building and electrical safety standards apply regardless of the rail's operating voltage, so don't assume "low voltage" means no licensed trade is required.

Does a 12-volt towel rail use less power than a standard 240V electric rail?

The operating voltage is about how the power is delivered, not necessarily a direct measure of running cost. What determines running cost is the rail's wattage, typically in a similar 60W to 150W range as standard electric rails, so it's worth checking the wattage rating of the specific product rather than assuming a lower voltage automatically means lower running costs.

How is a 12-volt heated towel rail different from a hydronic one?

A 12-volt or other low-voltage rail is still an electric product, drawing power through a transformer, whereas a hydronic towel rail is heated by circulating hot water from the home's existing hot water or heating system, with no direct electrical connection to the rail itself. Hydronic systems typically need to be integrated with your plumbing and heating setup at the design stage, while electric options including 12-volt rails are generally easier to retrofit into an existing bathroom.