Bath fillers buying guide
A bath filler is the tap that fills the bath. It can be a floor mounted mixer beside a freestanding bath, a wall mounted spout with a mixer, or a mixer set into the deck of a built-in bath. This page holds bath fillers in brushed nickel, gold, bronze, chrome, gunmetal, brass, black, graphite and white, from several brands. The guide below sets out the types, which suits which bath, how to check the reach and the height, how much flow to expect, and how to fit and look after one.
Types of bath filler
Match the type to the bath and the wall. This table sets out the main choices.
| Type | Where it fits | Check before you order |
|---|---|---|
| Floor mounted filler | Beside a freestanding bath | Pipe position and floor build-up. See freestanding bath mixers. |
| Wall mounted spout and mixer | Bath against a wall | Pipe centres and spout projection. See wall basin and bath mixer sets. |
| Swivel wall spout | Bath beside a basin or an offset bath | Projection and height above the rim. See swivel bath spouts. |
| Deck mounted filler | Built-in bath with a ledge | Hole size and ledge width |
For a freestanding bath away from a wall, a floor mounted filler is the natural choice. For a bath against a wall, a wall mounted spout keeps the floor clear. For a built-in bath with a ledge, a deck filler is the tidy option.
What a bath filler needs to do
A bath holds a lot of water, so a filler has to deliver a strong flow and land the water well inside the tub. That is why bath fillers often carry a lower WELS star rating than a basin tap: most on this page are 3 star, which reflects a higher flow rate that fills the bath in a reasonable time. Check the flow on the product page, and the pressure rating, because some floor mounted fillers need a minimum pressure. A bath filler on low pressure fills slowly, whichever tap you choose.
Are bath fillers any good
Yes, for the right bath. A bath filler gives a strong, direct flow, it frames the bath as a feature and it can be positioned to suit the layout. The points to weigh are practical: it needs more plumbing planning than a basin tap, a higher flow rate than a basin mixer, and the pipes have to be set before the floor or the wall is finished. If you want a simple, low-cost fit, a standard bath spout and mixer on a wall is the plainest choice. If you want a feature, a floor mounted filler gives the most impact.
Do you need taps with a bath filler
A bath filler is the tap, so a mixer filler needs nothing else to run. A spout-only outlet does not mix water by itself, and needs a separate mixer or a pair of wall taps to control it. A mixer filler includes the control, and a spout or an outlet does not, so check the product name before you order. If you are not sure, a wall basin and bath mixer set includes both the spout and the controls.
Choosing a filler for your bath
The bath decides the filler. A freestanding bath in the middle of the room suits a floor mounted filler. A freestanding bath against a wall can use a floor filler or a wall spout. A built-in bath with a tiled surround suits a wall spout and mixer or a deck set. A corner bath often suits a swivel spout. Measure the distance from the tap position to the middle of the bath, the height of the rim and the width of the ledge if there is one, and compare them with the product page.
Replacing an existing bath filler
A like-for-like swap is the simplest job. Look at the position of the old filler, how far it projects and how it is fixed, and compare those with the new one. If the new filler projects further or sits higher, the water will land in a different place, so check the rim and the tiles. Turn off the water before you remove the old filler, and ask a plumber to check the pipes and the fixings while it is off, because a worn support is the usual cause of a loose filler.
Reach and height
Check two measurements before you order: the projection of the spout over the bath, and the height of the spout above the rim. The water should fall well inside the tub, not on the rim, so measure from the tap position to the middle of the bath. The bath fillers on this page reach from about 175mm to 300mm, with tall floor mounted models standing much higher. The spout should clear the rim with room for your hand, and it should not sit so high that the water splashes.
Floor mounted fillers and the plumbing
A floor mounted filler stands on the floor beside the bath, and the supply pipes come up through the floor or from the wall behind it. The plumber sets the pipes before the floor is finished, so the position of the bath and the filler has to be decided first. Each maker publishes a rough-in sheet for its model with the hole size and the height the fitting finishes above the floor, so take the sheet for your exact model and give it to your plumber and your tiler.
Wall mounted fillers and the plumbing
A wall mounted filler needs the body in the wall before the wall is sheeted and tiled. The mixer sits beside the spout, or below it, and the plates cover the openings. Decide the spout height above the bath rim with your plumber before the wall is closed, and check the pipe centres of the set. If you want a spout that turns, choose a swivel. If you want the controls and the spout together, choose a wall set.
Deck mounted fillers
A deck filler fits through holes in the ledge of a built-in bath, and the plumbing runs below. It suits a bath with a wide ledge and a tiled surround, and it keeps the wall clear. Check the hole size and the number of holes on the bath, because a three piece deck set needs three holes and a mixer needs one. Leave room around the tap for your hand and for cleaning.
Hand showers on bath fillers
Some floor mounted and deck fillers include a hand shower on a hose, which is useful for rinsing the bath and washing hair in a bathroom without a separate shower. Check the hose length against the size of the bath, and the position of the cradle. For hand showers on their own, see hand held shower heads.
Cartridge, body and lead-free rules
We recommend a solid brass body and a ceramic disc cartridge. A ceramic disc cartridge uses two ceramic plates to control the water, resists wear and shuts off cleanly for years. The cartridges here are mostly 35mm, and the bodies are brass, lead-free brass, DZR brass and 316L stainless steel, which suits coastal bathrooms. The National Construction Code limits lead in plumbing products that touch drinking water to 0.25 percent from 1 May 2026. Check WaterMark approval on the product page, and use a licensed plumber to fit the filler and to test the pipes before the wall or the floor is closed.
Choosing a finish
A bath filler is a large, visible fitting, so the finish matters. The finish process differs by colour: chrome and matte black are mostly electroplated, while brushed nickel, brushed gold, brushed bronze, gunmetal and graphite are mostly PVD, which bonds the colour to the metal and resists scratching and tarnish. Match the finish to the basin mixer, the shower and the towel rail.
- Chrome suits white rooms and classic baths. See chrome taps.
- Matte black gives contrast against a white bath. See black taps.
- Brushed nickel is soft and muted. See brushed nickel tapware.
- Brushed brass and gold are warm against timber and marble. See brushed brass taps and gold taps.
- Gunmetal and bronze are dark and warm. See gunmetal tapware and bronze taps.
Caring for a bath filler
Wipe the spout, the handles and the standpipe with a soft microfibre cloth and warm water, and add a little mild soap if needed. Dry them so water does not set on the surface, which matters most in hard water areas. Avoid bleach, harsh sprays and abrasive pads, which dull a finish and can strip a coating. Wipe the plate or the floor seal, where water collects. If the filler drips from the spout when it is off, a new cartridge is the usual fix.
What comes in the box
The contents depend on the filler. A bath filler comes with the spout, the mixer or handles and an installation kit, and the in-wall or floor fixing parts, the hoses and a hand shower may be included or sold separately. Read the product page for the exact list before you order, and ask your plumber which fixing kit your bath needs.
Bath fillers by brand
The bath fillers on this page include Nero taps, Caroma taps, Phoenix taps, Meir taps, Fienza taps and Modern National tapware. Staying with one brand and range keeps the handle and finish consistent through the bathroom. For the shower side see shower mixers, and for the full group see taps.


