Skip to content

Bath Connectors

0 Items

Whoops, there are none available in your area

View all products

Bath connectors guide


A bath connector joins the bath waste to the drain when the two do not line up. It is a flexible section of pipe, with an elbow, that bridges the gap between the waste fixed to the bath and the trap or the pipe below. This collection holds the ART Australia Bath Bend Pop Down and Connector in several finishes, a plain ART Australia 40mm flexible bath connector, and a Decina flexible bath connector that comes with a pop-up waste. The sections below cover when a connector is needed, how far each product can reach, and what the pipework has to allow, so the part is chosen before the bath is set. For every bath waste type, start at bath wastes.

When a bath needs a connector

A bath waste sits in the base of the bath and the drain sits in the floor or the wall, and the two do not always meet. When the waste and the floor waste do not line up, a flexible connector can bridge the offset, as long as the pipe keeps its fall. A second check matters too: the space under the bath has to clear the length of the waste tail, so measure the clearance before the bath goes in.

Three situations call for a connector. An offset between the waste and the drain is the first. A freestanding bath is the second, and the ART Bath Bend has a low body that suits free standing baths. Limited space beneath a bath or spa is the third, and the ART Australia connector accommodates varying angles and gradients where that space is limited.

ART Australia bath bend pop down and connector

The Bath Bend is a pop down waste and a connector supplied as one set. It combines the plug and waste with a 600mm flexible connector and an elbow. The key numbers are a 40mm outlet, a body height of 77mm, a connector length that adjusts to a maximum of 600mm, a bath thickness of up to 12mm and a maximum offset of 650mm. It is overflow compatible and suits overflow or non-overflow baths, and the screws are variable to suit different bath thicknesses.

The 77mm low-height body is the feature that matters most for a freestanding bath. The low body suits free standing baths and installation is a top fix, from above. The waste itself is the flush type and sits flush in its open position, so there is nothing raised to sit on. A quick-remove cartridge comes out for cleaning, maintenance and access to the drain. The brand was previously known as Bounty Brassware, and the full range is on Bounty Brassware.

Finishes are Chrome, Gloss White, Matte Black, Brushed Nickel, Brushed Gold, Gold, Gun Metal Grey, Brushed Gun Metal Grey and Polished Brass. The Polished Brass is a raw brass finish that is not coated and is designed to patina over time. The other finishes are coated. The Gold is a polished gold finish, and the two grey versions are Gun Metal Grey and Brushed Gun Metal Grey. The specification is the same across finishes, so the choice is a style one: match the waste to the bath tap or the bath's own fittings.

The ART Australia 40mm flexible bath connector

The plain 40mm connector, in white, is for a bath that already has a waste. It incorporates the plug and waste, a 600mm flexible connector and an elbow, made for accommodating varying angles and gradients where space beneath a bath or spa is limited, and it is Water Mark approved. The collection carries the white finish only. Choose it when the bath is white, or when you need the connector and the waste in a plain white set.

The Decina flexible connector with pop-up waste

The Decina connector comes with a chrome pop-up plug and waste, a 40mm pop down waste. The flexible tube can be cut shorter to the length needed, and its smooth internal bore allows the bath to move when it takes large volumes of hot water. The tube is 300mm long and suitable for solvent welding. There is one firm limit: this waste only works with baths that have at least 100mm of room underneath.

The specification block lists brass and PVC construction, an electroplated finish, a surface diameter of 70mm and a G1 1/2 inch thread. The Decina tube is 300mm and is cut to fit, where the ART connector adjusts in length to 600mm. The first number to check on any connector is the distance between the bath outlet and the drain, because that decides which one will reach.

Pop down, and why it suits a bath

On this site pop down means a waste that sits flush when open, and pop up means one that sits proud with a dome. A flush waste suits a bath because there is no raised cap to sit on, and the ART wastes are that type. The removable cartridge can be taken out without a plumber and the centre button comes out, and hair and toothpaste build-up should be cleaned out to prevent jamming. The useful facts are plain: push to close, push to open, lift the cartridge out to clean.

How the cartridge works

A universal pop down waste is a quick-close waste that sits flush when open, with a removable cartridge that has polymer fins and a vortex design meant to keep the flow high. A slot near the top is intended to catch rings and earrings before they fall down the drain. The cartridge can be removed without a plumber, and the centre button comes out. Clean out hair and toothpaste build-up to prevent jamming, and use a soft cloth and warm water on the finish.

The ART Australia wastes work the same way: push to close, push to open, no levers to adjust, and a solid brass stopper that stays flush when open. To clean one, lift the stopper out, wipe it and put it back. Test the action in the first week and check that the cartridge lifts out before the bath is fixed in place.

Bath outlets are 40mm

The size on every connector here is 40mm, and that follows how baths are made. Basins are usually 32mm and baths 40mm, and larger fixtures such as baths take 40mm. A plain brass 40mm waste suits freestanding stone baths, vessel basins and timber vanities without an overflow, and it fits standard Australian plumbing for baths and larger vanity basins. Measure the diameter of the old plug or of the mesh, because sizes vary and leaks come from loose seals or poorly fitted wastes.

When the old waste is still in the bath, take it out and compare it with the new connector before ordering. When the bath is new, check the outlet size and the overflow arrangement in the bath's specification first, since the waste and the connector follow from that.

Removable baskets and access rules

The National Construction Code may require fully removable baskets for trap access, depending on the bath style and location. The Bath Bend's removable cartridge gives access to the drain from above, and the connector's inspection access gives it from below. Confirm with the plumber or the certifier what your job needs. The plain facts are that access is a design decision made before the bath is set, not a repair done afterwards.

Overflow and non-overflow

A bath with an overflow hole near the rim needs a waste that works with it, and a bath with a solid rim needs the other kind. The ART Bath Bend suits either, and is overflow compatible. An overflow is a small round hole near the top edge of the tub that sends excess water down the drain instead of over the edge. It drains slowly, running taps can still overwhelm it, and it needs cleaning now and then. For a choice of bath wastes that include an overflow, see bath wastes with overflows.

What the pipework has to allow

A connector is only as good as the route it follows. Dry-fit the bath first and mark the waste, then check the trap line against the rough-in. The waste connector should meet the trap without stress, kinks or upward bends. A flexible connector needs a clear route and inspection access. Forcing fittings causes leaks or slow drainage. Silicone goes on a clean, dry base, and it needs time to cure. The job ends with a fill-and-hold leak test that checks the joints below the floor.

Fall matters too. The pipe has to keep its fall after the connector, so the connector should lead downhill to the trap and should not sag into a low spot where water would sit. A bath connects by an untrapped waste of at least DN40 to a floor waste gully, or through a trap and a waste of at least DN40. Those are plumber's details, and they are why the outlet size of 40mm is the first number to match.

Care and cleaning

Lift out the cartridge or plug, rinse off hair and soap, and wipe the seat before pressing it back. Use a soft cloth and a mild detergent on the finish, and avoid abrasive pads and strong chemicals. Avoid vinegar on PVD in particular, because vinegar and abrasive cleaners can damage it. The connector itself is out of sight, but the inspection access is there for a reason: if the bath drains slowly, the trap and the connector are the first places to look.

How to choose

Measure first. Find the distance and the height between the bath outlet and the drain, and the clear space under the bath. If the offset is up to 650mm and the bath is 12mm thick or less, the ART Bath Bend is built for it. If a 300mm tube will reach, the Decina is made to be cut to length, and it needs 100mm of room beneath. If only the connection needs replacing, the plain 40mm ART connector does that job. Then choose the finish to suit the bath and the taps. The baths these connectors serve are on bathtubs, and the parent page for every maker's wastes, traps and grates is wastes, traps and grates.

Frequently Asked Questions

Do you offer warranties on your products?

Yes. All products come with manufacturer warranties, which vary by brand and product type. Warranty periods and terms are listed on individual product pages, and our team can help clarify coverage for any item before you purchase.

Do you offer products for both new builds and renovations?

Yes. Whether you're renovating an existing bathroom, kitchen or laundry, or fitting out a new build, our range is designed to suit both projects. We stock everything from budget-friendly essentials to premium designer pieces, including full suites from brands like Caroma and statement pieces from Bao Bath and Phoenix.

Are your products compliant with Australian Standards?

Yes. All products sold through The Blue Space meet the relevant Australian Standards and WaterMark certification requirements where applicable, so you can install with confidence knowing your fixtures are compliant for use in Australian homes.

What types of products does The Blue Space offer?

The Blue Space stocks a comprehensive range of bathroom, kitchen and laundry products, including tapware, showers, toilets, basins, baths, vanities and accessories. Our range spans trusted Australian and international brands such as Caroma, Bao Bath, Ingrain, Timberline, Phoenix Tapware, Nero Tapware and Meir, giving you options across every style and budget.