Skip to content

Brick Bond Tiles

0 Items

Whoops, there are none available in your area

View all products

Brick bond tiles: rectangular tiles laid in a running offset

Brick bond is a laying pattern. Each row of tiles is shifted along so the joints in one row fall near the middle of the tiles in the next, the way bricks are laid in a wall. This collection holds the rectangular and square tiles in the store that carry the brick bond layout tag, in ceramic and porcelain, from 100 x 100mm and 65 x 265mm subway tiles to 300 x 600mm and 600 x 1200mm planks.

The sections below explain brick bond and how it differs from stack bond and a third offset, what the main ranges are, which tiles suit walls and which floors, and how to plan the joints and the order. For tiles that look like brick, see the brick look tiles collection. For the same tiles in other layouts, see the subway tiles collection, the herringbone tiles collection and the basketweave tiles collection.

What brick bond is

Brick bond, also called stretcher bond, is a traditional laying pattern with a Victorian heritage. Each tile overlaps the tile above and below by half, which gives offset grout lines. Offsetting the grout lines hides imperfections in the tiling and in walls that are not perfectly straight, and the pattern gives an illusion of space and height. Allow extra for cuts and breakages.

The same layout is called running bond with a half offset, and it is the original subway tile layout: tiles laid horizontally with each row offset by half a tile length, mimicking a brick wall. It is the safest choice and works in virtually every style. You will see the words brick bond, running bond, stretcher bond and brick lay used for the same thing.

Brick bond and stack bond

Stack bond is the other everyday layout, and the difference is the joints. In a stack bond the tiles sit directly above one another, so the joints form a continuous grid. A vertical stack is a perfectly aligned vertical grid that draws the eye upward and makes a ceiling feel taller, and a horizontal stack gives clean horizontal lines that visually widen a room.

In brick bond the offset breaks up the straight vertical lines, so the surface reads as a field of tiles and not a grid. That is why it is a good way to add flair without taking attention from a focal point. Stack bond makes the grout the design. Brick bond makes the grout less visible. The tiles in this collection carry both layout tags, so you can choose.

The third offset

A staggered brick bond, or one-third stretcher bond, is a favourite for large format rectangular tiles. The tiles overlap the row above and below by one third instead of half, which gives a contemporary feel and the appearance of a larger room. The layout can be used with any tile size but is commonly used for larger tiles.

There is a practical reason. Longer, larger tiles are rarely perfectly flat and tend to curve up slightly in the middle. A half offset puts the low ends of some tiles beside the raised centres of others, creating lippage, the small ridge between neighbouring tiles. Offsetting by about a third spreads the edges so they meet less often. The difference is minimal with smaller tiles. For the 300 x 600mm and 600 x 1200mm tiles here, ask your tiler whether a third offset suits the tile and the subfloor.

The tiles in this collection

The tiles sort into groups by size and look. These show the spread.

The small tiles are wall tiles. Bella is a 65 x 265mm mini subway in matte and gloss, rectified, with a P2 line and Application Walls, and it needs no sealing. The Dianna and Luca ranges are 75 x 150mm hand made look subway tiles, and the Ella and Dianna zellige look squares are 100 x 100mm. Ella is an Italian made ceramic with a wavy structured gloss glaze, made for walls and splashbacks.

The longer subway tiles include Theo, 75 x 400mm Italian porcelain, Leon, 69 x 240mm Spanish gloss ceramic, Olivia, a 75 x 300mm Italian feature subway, and Blaire, a 45 x 230mm textured brick tile. Olivia is a matte tile with raised feature strips, and Blaire pairs best with a light grout.

The larger tiles are 300 x 600mm and 600 x 1200mm porcelain. They include Burleigh, a cushioned edge stone look, Island Terrazzo, a matte P4 terrazzo look, and Casuarina, a stone look in matte P4 and honed finishes. For these sizes in their own right, see the rectangle tiles collection and the 600mm x 1200mm tiles collection.

Walls and floors

Most of the collection is wall tile. The small subway tiles carry Application Walls or Wall Tile, and Ella has a wear line of 0. The floor-rated tiles are the larger porcelain ones. Island Terrazzo carries Application Walls and Floors and a Wear Rating of 4, suitable for floors in normal use areas with a low risk of scratching. Its slip rating is P4, low slip risk and best for outdoor areas. The Casuarina matt P4 tile has a Wear Rating of 4 and can be used in entrances, laundries, patios and more.

AS 4586 classifies the slip resistance of new pedestrian surface materials, and its wet pendulum test uses ratings from P0 to P5. The rating applies to floors people walk on and does not matter for a feature wall. Confirm with your builder or tiler what a floor needs, and read the Application, Wear Rating and Slip Rating lines together before you choose. The floor tiles collection and the wall tiles collection sort tiles by use.

Grout colour

Grout tips are short and useful. For a running bond, white grout creates a continuous look and gray grout adds subtle definition. Light grout creates a softer wall, while mid-tone or darker grout makes each tile more defined, and dark grout may disguise some marks but still needs regular care.

In a brick bond the grout colour sets how visible the offset is. A grout close to the tile colour lets the offset disappear into a continuous field. A contrasting grout draws the brick pattern, which is the look of a brick wall. Check the colour against the tile in the room, and consider that a subway layout has more joints than a large tile, so there is more grout to clean over time.

Joints and spacers

Most of the rectified tiles in this collection print a recommended gap of 1.5 to 3mm. Spacers come in 1.5, 2 and 3mm widths and are placed with one arm in the gap between tiles to hold a constant space until the adhesive sets. They are not embedded in the grout and must be removed once the adhesive has dried and before grouting.

The cushioned edge tiles are different. Cushioned edge tiles such as Burleigh have natural irregular edges and need grout lines of 3mm or more for a classic tiled appearance. A cushion edge tile most likely needs a joint of 3 to 5mm, while rectified tiles can have tight joints. In a brick bond the joints are also a design line, so agree the width with your tiler before ordering.

Where brick bond is used

Brick bond subway layouts work well in bathroom and shower walls, kitchen splashbacks and laundries, provided the tile suits the intended wall and wet-area use and forms part of a compliant waterproofing and tiling system. The tile, adhesive and grout sit over the waterproofed surface and do not replace the waterproofing itself, and the National Construction Code sets out the wet-area waterproofing requirements.

That applies to every wall tile in this collection. The tile is the visible layer. The membrane behind it is a separate job for a licensed waterproofer, and installation must be carried out by a licensed tiler to the appropriate Australian standards. For room-led collections, see the bathroom tiles collection and the kitchen tiles collection.

Ordering extra

Order an extra 10 percent spare at least, because tiles are produced in batches and different batches may not match. Order an extra 15 percent over the exact quantity to cover breaks and offcuts, because brick bond needs extra for cuts. The higher figure is the safer start for an offset layout with many edge cuts.

A worked example: a splashback 3m wide and 0.6m high is 1.8 square metres. A 75 x 150mm tile covers 0.01125 square metres, so the wall takes 160 whole tiles, and with 15 percent for cuts the order is 184. A 65 x 265mm Bella covers 0.017 square metres, so the same wall takes about 106, and 122 with the allowance. Plan the first row from the centre of the wall so the end tiles are matched, and order every box together so the glaze matches.

Place one order for the full quantity. Colour, size and texture can vary from batch to batch, and keeping a few spare tiles stored is also wise.

Before fixing, check the wall for flatness with a long straight edge. A brick bond hides small faults better than a stack, but a wall that is out by more than a few millimetres needs levelling first, because the offset joints cannot cover a bow in the wall. Use the same adhesive bed depth across the whole wall, and press each tile in with a slight twist so the offset joints stay straight. Wipe grout haze off the face as you go, and leave the joints to cure before the first clean.

Choosing a tile and a layout

Start with where it goes. For a shower wall or splashback, the small subway tiles in a half offset are the classic choice. For a feature wall, a vertical stack or a stepladder arrangement draws the eye up, and a stepladder, or vertical brick bond, creates the illusion of height. For a floor, look at the larger porcelain tiles with a floor wear line.

Then settle the joint and the layout. Order a sample, lay it dry, and look at it in the light of the room. For other layouts that use the same tiles, see the herringbone tiles collection, and for every shape and finish in the store, the tiles collection.

Frequently Asked Questions

What is the best tile finish for a bathroom, matte or gloss?

Matte tiles are trending strongly in Australian bathrooms for their contemporary look and practical ability to hide water spots and fingerprints. Gloss tiles reflect light and can make a bathroom feel brighter and larger, but show water marks and smudges more readily. For shower recesses and wet floors, matte or satin finishes with good slip resistance are generally preferred.

How many tiles do I need to order for my bathroom?

Measure your total wall and floor surface area in square metres, then add a 10–15% wastage allowance for cuts, breakages, and future repairs. For complex layouts with diagonal patterns or feature inserts, increase the wastage to 15–20%. Always order all tiles from the same batch (check the shade lot/batch number) as tiles from different batches can vary slightly in colour.

How do I choose between floor tiles and wall tiles?

Floor tiles must have an adequate slip resistance rating (P3 minimum for domestic bathrooms) and be durable enough for foot traffic. Wall tiles can be glazed ceramic, porcelain, or natural stone, they don't need to carry load but should be moisture-resistant. Many Australian renovators choose matching or coordinating floor and wall tiles from the same range for a cohesive look.

What tile size is best for a small bathroom in Australia?

For small bathrooms, tiles between 300 x 300mm and 600 x 300mm often work well on both walls and floors. Smaller mosaic or subway tiles (75 x 150mm or 100 x 200mm) are a classic choice for shower walls. While large format tiles can also work in small spaces, they require a very level substrate and expert installation. Avoid tiles that are too small on floors (like 50 x 50mm mosaics) in large quantities, as the increased grout lines can make a space feel busier.

How do I incorporate feature tiles without over-designing the bathroom?

The most effective approach is to choose one feature zone and use your feature tile there, a full-height shower wall, the bath surround wall, or the vanity splashback area. Keep the remaining surfaces in a neutral or complementary field tile. This creates impact without visual clutter. Limit your palette to two or three complementary materials for a cohesive result.

What is the slip resistance rating I need for bathroom floor tiles?

Australian Standards (AS 4586) require bathroom floor tiles to have a minimum slip resistance rating of P3 for domestic bathrooms and P4 or P5 for wet areas like shower recesses. The Blue Space recommends checking the slip resistance rating of any tile you're considering for floor use, particularly in the shower. Matte and textured porcelain tiles generally offer better slip resistance than polished or gloss finishes.

What is the difference between ceramic and porcelain tiles?

Porcelain tiles are fired at higher temperatures and are denser, less porous, and harder than ceramic tiles. This makes porcelain more water-resistant, more durable, and suitable for both indoor and outdoor applications, including high-traffic floors. Ceramic tiles are lighter and easier to cut, making them a practical choice for bathroom walls and splashbacks. For bathroom floors and wet areas, porcelain is generally the preferred option in Australia.

What is a brick bond tile pattern?

Brick bond (sometimes called running bond or offset lay) is a layout where each row of rectangular tiles is shifted sideways from the row above it, the way bricks are staggered in a traditional brick wall. It's a layout technique, not a tile finish: you can lay brick bond with a plain matte tile, a gloss tile, a stone-look tile or a plain white subway tile. If you're after a tile whose surface actually looks like brick, that's a different product, see our brick-look tiles range instead.

What offset is typically used for a brick bond layout?

A half (50%) offset, where each tile sits centred over the join of the tiles below it, is the most common and traditional brick bond spacing, and it's the layout most people picture when they hear the term. A third (33%) offset is also used, particularly with longer plank-format tiles, because it spreads the joins more evenly and can reduce the visual "stepping" effect that a strict half-offset sometimes creates with very long tiles.

Does brick bond tiling take longer to install than a straight grid?

It generally takes a bit more time and planning than a straight (stack) lay, since the tiler needs to set out the offset carefully to keep the joints consistent across the whole area, and end rows will usually need cuts to maintain the pattern. It's still considerably quicker than a diagonal or herringbone layout, since the tiles stay square to the walls rather than being angled, so cuts are simpler.

Can brick bond be used with large format tiles?

Yes, and it's a popular choice for rectangular large format tiles such as 300mm x 600mm or similar plank sizes, since the offset breaks up what could otherwise be a very uniform grid of long joints. With very large tiles, ask your tiler about the offset percentage; a full half-bond on an oversized plank tile can occasionally look awkward, and a third-offset is often recommended instead.

Is brick bond suitable for both floors and walls?

Yes, it works on both. On floors it's common in hallways, kitchens and living areas with rectangular tiles. On walls it's a familiar look for splashbacks and shower walls, especially with subway-style tiles, where the offset pattern is part of the classic look. The tile's own slip rating and water resistance still need to suit the location; the brick bond layout itself doesn't change those properties.

How much extra wastage should I allow for a brick bond layout?

Slightly more than a straight grid, generally in the 10 to 15 percent range, to cover the cut tiles needed at the start and end of each offset row. It's a more modest allowance than a diagonal or herringbone pattern needs, since the tiles stay aligned to the wall rather than being cut at an angle.