Skip to content

Decina Alegra Freestanding Spa Baths

0 Items

Whoops, there are none available in your area

View all products

Decina Alegra spa bath buying guide


The Decina Alegra is a back to wall freestanding spa bath with curved edges, generous reclining lumbar supports and a centre waste that makes it suit two bathers. This page holds it in two lengths, 1500mm and 1700mm, each with white jets or chrome jets, which makes four versions of one spa bath. It sits flush against a bathroom wall, with the pump mounted through the wall, either outside the room or in an adjoining space, and it is controlled from a rim mounted touch pad. This guide explains how the Alegra works, sets the four versions side by side, and covers power, waste, floor and fit before you order. For spa baths from every maker, see spa baths, and for the whole Decina spa range, Decina spa baths.

The four versions

Version Length Jets Capacity Weight
Alegra 1500 white jets 1500mm White 162 litres 60kg
Alegra 1500 chrome jets 1500mm Chrome 162 to 175 litres 60kg to 65kg
Alegra 1700 white jets 1700mm White 175 litres 65kg
Alegra 1700 chrome jets 1700mm Chrome 162 to 175 litres 60kg to 65kg

Every version is 800mm wide and 590mm high, in high gloss white premium sanitary grade acrylic. Capacity is measured 200mm below the bath rim, which is a lower fill line than the overflow, so it is the water you would normally run and not the volume to the brim.

How the Alegra sits in the room

The Alegra is designed to sit flush up against a bathroom wall, with its other sides finished, so it keeps the look of a freestanding bath and leaves no gap behind it for dust to collect. The pump is mounted through the wall, either outside the bathroom or in an adjoining room, which keeps the machinery out of sight and out of the bathing space. That is the key planning point: the wall behind the bath has to allow for the pump, and the pump has to stay reachable for servicing. Adjustable self-supporting feet let the bath be levelled on a floor that is slightly out of true. For the type across every maker, see back to wall baths.

Jets and controls

Each Alegra has four flush centro jets, eight flush mini jets and one flush suction, with a rim mounted touch pad that controls the bath. You choose white jets or chrome jets, which changes the look of the fittings and not the performance. The lumbar supports are generous and recline, so the bather can lean back against them, and the curved edges give the shell a soft outline. A spa bath adds a pump and jets to the same acrylic shell, so it is still a bath for soaking as well as a spa.

The pump and the power

The Alegra has a 750 watt TriFlo Eco pump and a 700 watt heater. The supply is 240 volts and the current is 7.5 amps with the heater, and the flow rate is 350 litres per minute. The electrical connection is a job for a licensed electrician, and it needs to be planned with the builder before the walls are closed, because the pump is mounted through the wall and its wiring has to reach the controls. Confirm the supply and the position of the pump before you order, and leave access to the pump, the air control and the heater so they can be serviced without opening the wall.

Dual bathing

The waste sits at the centre of the bath, which suits dual bathing: two people can sit at either end without the plug under a back. Each end has a lumbar support, so both bathers are held in a reclined position. An 800mm width gives room for two, and the 1700mm length is the better choice for sharing. If you will bathe alone, the centre waste is still useful, because the bather can sit at either end.

A heater in a spa bath

A spa bath is filled fresh for each use, and many spa baths have no heater, so a long soak cools as it goes. The Alegra has a 700 watt heater alongside its 750 watt pump, so the water can be kept warm during the soak, which is the main advantage over a plain bath of the same size. The heater adds to the current, which is why the Alegra draws 7.5 amps, and it is one of the figures to give your electrician. If you want to soak for a long time, this is the feature that makes the bath comfortable, and it is worth planning the power for it from the start.

Planning the wall with your builder

Because the pump is mounted through the wall, the wall behind the bath is part of the bath. Agree its construction with your builder before the framing is closed: the opening for the pump, the cable run to the controls, and the access to the pump from outside the bathroom or from the adjoining room. Leave a way to reach the pump later, because it will need servicing, and a pump sealed behind tiles can only be reached by breaking them. The wall also takes the tapware pipes, so the builder, the plumber and the electrician should agree the layout together.

What the touch pad controls

The rim mounted touch pad is the control for the bath, and it sits on the rim within reach of the bather. Because it is mounted on the rim, plan the position of the tapware and any shelf so the pad stays clear. The touch pad is the part of the bath the bather uses, so check its position on the product page before you decide where the taps go.

The Alegra and a plain bath

The Alegra also comes as a plain back to wall bath without jets, in 1400mm, 1500mm and 1700mm, with an integrated overflow. If you want the shape and the flush wall position without the pump and the jets, the plain bath is simpler and needs no power. If you want the jets, the heater and the controls, the spa is the one. The spa is a more involved installation, with a pump, a cable and an access point, and the plain bath is a plumbing job only. Think about how you will use the bath before you choose.

Installing the Alegra

The order of work matters. The builder frames the wall for the pump, the plumber roughs in the waste and the supply pipes, and the electrician runs the cable to the pump and the controls. The bath is set in position on its adjustable feet and levelled, and the pump is connected through the wall. The wall junction is sealed with flexible, mould resistant silicone after the tiling, and the bath is tested before the room is finished. Keep the installation instructions with the bath, since the electrician and the plumber will both need them.

Overflow and waste

The Alegra comes with an overflow as standard, and an in-line waste connection with a built-in connector pipe, so the overflow and the waste are joined in the bath. The plug and waste finish is a separate choice, since the box holds the bath. Pop-Down wastes are the better choice for safety, service and maintenance, and Australian building codes require a fully removable bath waste in some situations, so ask your plumber before you order. The bath wastes collection has the options.

Weight and the floor

The Alegra is a light spa bath, from 60kg to 65kg empty. Water adds roughly 1kg per litre, so a full bath holding about 175 litres adds about 175kg, and two bathers add more. The floor needs to be sound and level, a timber floor should be checked before installation, and the route into the room should be measured, since a bath of 1700mm may not clear a standard 820mm doorway when it is carried upright. The adjustable feet correct a slight slope and do not replace a floor that is weak.

Choosing 1500mm or 1700mm

The 1500mm bath suits a short wall and a smaller bathroom, and it is the short end of the standard range. The 1700mm bath gives more length for a taller bather or for two, and it needs a longer wall. Both are 800mm wide, so the floor beside the bath is the same. Measure the wall, the door swing and the route into the room, then compare the bath length with the space, and leave a small gap at the end for sealant. 1500mm baths and 1700mm baths list each length across every maker.

Tapware

The tapware follows the position. A back to wall bath takes wall mounted tapware, with the pipes in the wall behind the bath, and the pump and the supply pipes share that wall, so plan them together before the tiling. A floor mounted spout or mixer can also stand beside the bath. Decide before the plumber roughs in, because the pipework is behind the tiles once the room is finished.

A shower over the Alegra

For a comfortable shower over a bath, the bath should be at least 1500mm long and 700mm wide, with a screen of at least 1400mm, and both Alegra lengths meet it. The wall behind a back to wall bath holds the screen. The waterproofing runs well up the walls and past the bath edges, and it needs its full cure time before tiling. Shower baths lists the full set.

Care

Acrylic can be cleaned with warm soapy water or a liquid polish. Rinse the bath after each use and wipe it with a soft sponge or microfibre cloth, and keep abrasive powders and steel wool away from the surface. A spa bath needs more care than a plain bath because water sits in the pump and the jet lines, so after bath oils, refresh the pipework by running the jets with clean water. Check the silicone seal along the wall each month.

Choosing an Alegra

Start with the wall and the pump position, because the pump goes through the wall. Then choose the length, and the jet finish, white or chrome. Plan the electrical connection with a licensed electrician, confirm the waste, and plan the tapware and the floor. For the Alegra without jets, see Decina baths, and for every bath at every length, bathtubs.

Frequently Asked Questions

What is a spa bath and how does it work?

A spa bath is a bathtub fitted with jets that pump pressurised water or air through nozzles in the bath walls to create a therapeutic massage effect. Water jets provide a deep-pressure massage, while air spa systems create a gentler, bubbling sensation. Some models combine both systems for a customisable experience.

Are spa baths hard to maintain?

Spa baths require more maintenance than standard baths. The jet system, pipes, and pump need to be cleaned regularly to prevent bacteria and biofilm buildup inside the plumbing. Most spa baths have a self-cleaning or purge cycle that should be run after each use. Using appropriate spa bath cleaning products (not standard bathroom cleaners) is essential for maintaining the internal pipework.

Do spa baths require special plumbing or electrical connections?

Yes. Spa baths require both standard plumbing connections (hot and cold water, waste) and a dedicated electrical connection for the pump and controls. This must be installed by a licensed electrician and plumber. The bath location must be accessible for the motor in case of maintenance or replacement. Discuss these requirements with your trades early in the planning process.

Are spa baths suitable for small bathrooms?

Most spa baths are built into alcove or corner configurations and are available in standard bath sizes (1500–1800mm), so they can fit in the same space as a regular built-in bath. However, the motor and pump require accessible housing, which may add to the spatial footprint. If a spa bath appeals to you but space is limited, a drop-in spa bath with a built-in surround is often the most compact option.