Skip to content

Liquid Filled Heated Towel Rails

0 Items

Whoops, there are none available in your area

View all products

Liquid filled heated towel rails buying guide

A liquid filled heated towel rail is an electric rail with liquid inside its bars. An immersion element warms the liquid, and the liquid carries the heat through the rail. People search for it as an oil filled, water filled or liquid towel rail, and the fill in the rails here is a mixture of water and glycol, not oil. It is a different kind of rail from a dry electric ladder: it holds a steady temperature and warms the room a little as well as the towel. The right call is a liquid filled rail when you want a steady, warmer rail on a hardwired circuit and you are happy to put it on a timer. This guide sets out how it works, how it compares with a dry electric rail, how it is wired, controlled and fitted, and what it uses to run.

What liquid filled means

The bars of the rail are hollow and filled with liquid. The rails here are filled with a mixture of water and glycol, which stops the liquid freezing and stops corrosion inside the rail. The liquid also adds thermal conductivity, which is how the rail keeps a consistent temperature along its length. The rail arrives prefilled, with its legs and wiring attached, so there is nothing to fill on site. The body is 304 stainless steel, and the rail is made in Europe.

How it heats

A 300 watt immersion heating element sits inside the rail and warms the liquid. The liquid circulates through the rail system, which heats the bars that carry the towels. The bottom rail stays cool to the touch. Because the whole rail holds heat, it acts as a radiator in the room as well as a towel warmer, and it gives gentle warmth to the bathroom. The element is replaceable, so if it ever fails the rail does not have to be replaced.

Heat-up time and temperature

The rail heats to approximately 55 degrees, and it takes 15 to 30 minutes to get there. Liquid filled rails differ: a tall liquid filled ladder takes closer to an hour to reach 55 to 60 degrees. A liquid filled rail heats to around 55 degrees whether or not a towel is on it, and it holds a constant temperature once it is hot. That is different from a dry electric rail, which is about 35 degrees without a towel and 50 to 55 degrees under one. Some liquid filled rails have a thermostat built in, which controls the temperature of the rail itself. A rail without one is controlled by a timer or a switch.

Liquid filled or dry electric

A dry electric rail runs a heating cable through the bars. The cable heats the air in the bars, the towel insulates the rail, and the rail warms the towel. It warms in about 5 minutes, reaches its best temperature in about 30 minutes and is not designed to warm the room. Its running cost is similar to a 60 watt light bulb. A liquid filled rail has a 300 watt element, which is five times that figure. It reaches its temperature in 15 to 30 minutes on this rail and takes longer on a tall ladder, it holds a steady temperature and it adds some heat to the room. Choose the liquid filled rail when you want that steady warmth and a rail that works as a small radiator. Choose a dry electric ladder when you want a quick, low-wattage rail for towels alone. The heated towel ladders collection compares dry electric ladders, and 240V heated towel rails compares mains-powered rails of every kind.

The rails in this collection

Feature Detail
Finishes Chrome and brushed brass PVD
Size (width, height, depth) 600mm, 800mm, 122mm
Bars 5
Power 300 watts
Supply 230 to 240 volt, 50 Hz
Water protection IP44
Heats to About 55 degrees in 15 to 30 minutes
Weight 11.5 kg
Wiring Fully concealed, hardwired, bottom right only
Switch on the rail None

For a tall liquid filled ladder, see the floor to ceiling ladder rails collection.

Which style it suits

The rails here are sold for the traditional style, and they suit a traditional or Hamptons bathroom. Chrome is the finish for polished fittings, and brushed brass brings a warm tone that sits with antique and vintage looks. Match the finish to the metal already in the room, and keep one finish from the basin to the shower to the rail. The traditional style and Hamptons collections show how those rooms are put together, and brass and gold heated towel rails and chrome heated towel rails compare the other rails in those finishes.

Warmth for the room

All the power the rail draws becomes heat, and a liquid filled rail gives part of it to the room because the whole rail stays warm. That is gentle warmth, an additional source of heat while it dries the towels. If you want heat for the whole room, a ceiling heater is made for that job, and the bathroom heaters collection holds those units.

Size

The rail is 600mm wide and 800mm high, with five bars, and it stands 122mm out from the wall. Check the wall for that width and height, and remember the lowest heated rail has to sit at least 600mm above the floor. The wiring comes out at the bottom right, so plan the cable at that corner of the rail.

Controlling the rail

The rails here have no switch on the rail, for the way they look. Install the rail with a control panel timer, which preheats the towel before you use it, or connect it to a switch in the bathroom, as part of a power point or beside the light switch. A timer is recommended for more efficient control. A timer has to be installed in the correct zone for its IP rating, and it has to carry the load. The Eco Timer in the Thermogroup timers and thermostats collection is rated 1 amp, so it switches up to 240 watts and is not enough for a 300 watt rail. The Boost Timer and the Touch Screen timer are rated 16 amps, which is 3,840 watts, and controllers and thermostats helps you choose between them. Set the start time ahead of the shower, because the rail takes 15 to 30 minutes to heat.

Wiring

The rail is hardwired, with concealed wiring, and the wiring is always at the bottom right of the rail. The rail cannot be mounted upside down. Plan the cable in the wall at that bottom right position before the wall is lined, and have a qualified electrician connect it to the mains to AS/NZS 3000. The circuit has to be protected by a suitably rated RCD, and the fixed wiring has to include a means of disconnection.

Where it goes

The rail can be installed at least 600mm from a shower or bath. The lowest heated rail has to be at least 600mm above the floor, with 300mm clear of permanent fixtures, which protects very young children from the hot rail. Where possible, screw the rail into studs or battens hidden in the wall. The rail weighs 11.5 kg, so give it a solid fixing. The rail is hot to touch, so supervise young children and anyone who needs help near it.

Fitting the rail step by step

The box holds the prefilled rail with its legs and wiring attached, four wall flanges, twelve mounting screws, twelve wall plugs, six grub screws, twelve screw cap holders, twelve screw caps and an Allen key. You also need a cross head screwdriver, a pencil, a spirit level, a tape measure, a hammer, 10mm and 3mm drill bits, a cordless drill and the electrical supply. Then follow these steps:

  • Set the height of the rail with a ruler, level it with the spirit level and mark the position of the wall brackets.
  • Drill 10mm holes at the marks and hammer in the wall plugs.
  • Pass the mounting screws through the screw cap holders, place the bracket on the wall and screw it all the way in.
  • Fit the screw caps over the cap holders on the brackets.
  • Place the rail into the wall brackets.
  • Insert the set screws into the slots on the brackets and the rail, and tighten them with the Allen key.
  • With the power switched off, connect the rail lead to the mains supply.

Do not hang anything on the rail that has been in contact with oil, petroleum based products or dry cleaning fluids. Check the rail for defects before installation.

Care

Clean the rail with a soft cloth and a non-abrasive cleaning agent. Harsh scrubbing, scratching and acid based cleaning products damage the surface. Never immerse the rail in any liquid.

What it uses to run

The rail draws 300 watts. Divide the watts by 1,000, then multiply by the hours to get kilowatt-hours. The table shows a 5 hour day, a week of that routine and a rail left on for 24 hours, with a dry electric rail at 60 watts for comparison.

Rail 1 hour 5 hours 5 hours a day for a week 24 hours
Liquid filled rail, 300 watts 0.30 kWh 1.50 kWh 10.50 kWh 7.20 kWh
Dry electric rail, 60 watts 0.06 kWh 0.30 kWh 2.10 kWh 1.44 kWh

Multiply the kilowatt-hours by your own electricity rate to see the cost for your household. A rail left on all day uses almost five times the energy of the same rail on a 5 hour routine, so put a liquid filled rail on a timer and set the hours you need.

Where to go next

The full range is in heated towel rails.

Frequently Asked Questions

What does 'liquid filled' or 'oil filled' mean on a heated towel rail?

It describes the type of heating element inside the rail rather than its finish or shape. A liquid or oil filled rail circulates a heated liquid, often a thermal oil, through the tubing that makes up the rail, rather than relying on a dry electric element that only warms while switched on. The liquid holds and distributes heat through the rail's structure once warmed.

Does a liquid-filled towel rail stay warm after it's switched off?

Yes, this is the main practical difference from a standard dry element. Because the heated liquid retains warmth, a liquid-filled rail typically continues radiating heat for a period after being switched off, rather than cooling almost immediately the way a standard dry electric element does. How long that residual warmth lasts varies by model and rail size.

Is a liquid-filled heated towel rail better than a standard dry element rail?

Not universally better, it's a different way of achieving warmth with a genuine practical trade-off. The residual heat after switch-off suits someone who wants a warm towel available for a while after the rail is turned off, without leaving it running continuously. A standard dry element responds and cools more immediately, which suits someone who prefers precise, on-demand control with no lingering heat. Neither dries a towel meaningfully faster than the other for a given wattage.

How is a liquid-filled towel rail different from a hydronic one?

They're often confused but work differently. A liquid or oil filled rail has a sealed internal liquid heated by its own electric element, entirely self-contained within the rail. A hydronic rail instead connects into the home's existing hot water or central heating system, so its water supply comes from outside the rail itself. A liquid-filled rail is simpler to retrofit into an existing bathroom, since it doesn't need to tie into household plumbing or heating infrastructure the way a hydronic system does.

Do liquid-filled heated towel rails use more electricity than standard rails?

Not inherently, running cost still comes down to the rail's wattage rating rather than the heating method itself. Most electric heated towel rails, liquid-filled or dry element, draw somewhere between 60W and 150W, comparable to a household light bulb, though a liquid-filled unit may draw power in shorter cycles to maintain heat rather than running continuously. Check the specific wattage listed for the model you're considering rather than assuming based on the technology alone.

Does a liquid-filled heated towel rail need a licensed electrician to install?

It depends on the connection type rather than the heating mechanism. A plug-in rail that connects to a standard power point can usually be installed without an electrician, provided the point is correctly placed for the bathroom's wet zones. A hardwired rail, wired directly into the mains with no visible plug, must be installed by a licensed electrician under Australian electrical safety rules, the same requirement that applies to any hardwired towel rail.