Skip to content

Myra Limestone Tiles

0 Items

Whoops, there are none available in your area

View all products

Myra limestone tiles: what this range is

Myra is a limestone look porcelain range. The tile is porcelain with a printed and glazed surface that copies a pale Turkish limestone, and nothing in this collection is cut from the stone itself. That is the first thing to settle, because search results for limestone tiles mix the real stone and the look-alike on the same page.

The range is small. It is one tile in one colour and one finish, in three sizes: 300 x 600mm, 600 x 600mm and 600 x 1200mm. All three are 10mm thick. Because the tile does not change between sizes, the useful decisions are size, where it goes and how it behaves when wet, and this page is organised around those.

Below you'll find how limestone look porcelain differs from the real thing. After that come the sizes, the grip finish and P4 slip rating, where the tile can go, and what to read before you order. If you'd rather start wider, the main tiles collection sorts every tile by room, size, colour and material.

Limestone look porcelain or real limestone

Real limestone is sedimentary rock, formed at the bottom of lakes and shallow seas, where shells and other calcium rich material collect and settle into stone. That origin explains most of what people say about it: each tile is different, the tone is soft, and the surface is porous.

Limestone look porcelain is a different material made to resemble that stone. It is a porcelain body that is printed and glazed to copy the texture of the original, and fired at a very high temperature, which makes it close to impervious to water and stains. Real limestone is a little porous, with sealing at installation and again every year or two depending on use.

What that means for care

Limestone, travertine and sandstone are highly porous and absorb moisture unless they are sealed and resealed on a schedule. Porcelain has a water absorption of under 0.5 percent, which is the reason porcelain is the default for wet areas on the coast.

Myra sits on the porcelain side of that split. The tile does not need sealing and does not need regular maintenance, and the spec block reads maintenance as easy to clean. If you want the stone itself and accept a sealing routine, real limestone is the right material and this range isn't it. If you want the look without that routine, Myra is built for it.

Sizes and how they're listed

The three Myra sizes differ in how many pieces come in a box. Each box covers 1.44m2, so the piece count changes with the tile: 8 pieces of the 300 x 600mm tile, 4 pieces of the 600 x 600mm tile and 2 pieces of the 600 x 1200mm tile.

All three are rectified. The recommended grout gap for each size is 1.5mm to 3mm. Confirm the gap for the size you choose, because it is the figure your installer will work to.

300 x 600mm

This is the smallest size, a rectangle with a 300mm short side, and it carries the 8 piece box. It suits walls and floors like the other two, and splashbacks as well. It is the size to look at first for a small wall or splashback.

600 x 600mm

The square size. The 600mm x 600mm tiles collection lists every tile in this size across the catalogue, so you can compare Myra with other 600mm squares before you decide.

600 x 1200mm

The largest size, with the fewest joints across a floor. A matt beige limestone look porcelain in 1200 x 600mm is a common pairing of format and look. The 600mm x 1200mm tiles collection is the page to compare against.

Installation instructions come from your tiler. Ask the tiler who will lay them what they need before you order the biggest size.

Grip finish, P4 and wet areas

All three sizes have the finish Grip and the slip rating P4. The surface is a textured matt tech grip finish, and the feel is a soft matt texture. Put together, the tile is meant to be matt with enough surface texture to hold up when wet, not polished.

That matches the usual advice. Matte and textured finishes generally cope with wet conditions better than a polished surface, and slip rating deserves a close look in a bathroom or an outdoor area. A matt and textured finish is a finish decision, with grip retained when wet.

What P4 refers to

AS 4586 classifies the slip resistance of new pedestrian surface materials, and its wet pendulum test uses ratings from P0 to P5. The rating applies to floors people walk on, and it does not matter for a feature wall. P5 is the top of that scale, so P4 sits one step below it.

P4 is the rating the tile carries. For a bathroom floor or a covered outdoor area, a P4 grip tile is a sensible match, and the final call on a shower base or pool surround belongs to the person specifying the job.

Limestone tiles for bathrooms

Search demand for this collection includes limestone bathroom tiles, limestone tiles for the bathroom and limestone shower tile. The stone and the look-alike answer those questions differently. Real limestone in a wet room needs sealing and a gentle cleaner. Myra is porcelain, made for walls and floors and for splashbacks, with a grip finish that suits bathrooms.

If you are tiling a whole bathroom, the bathroom tiles collection shows what else the catalogue offers for walls and floors, and the floor tiles collection covers the floor side.

Limestone tiles for outdoors

One Myra size carries Indoors and Outdoors in its Area line, and the other two repeat it in the feel and suitability lines. Myra suits the area around a pool, paths and alfresco areas. A tile used outside should still be checked against the conditions of the site, such as sun, salt air or a shaded wet corner, and the outdoor tiles collection is the page to open if you want to compare options.

Where it can go

Two fixed lines cover placement. Application: walls and floors. Area: indoors and outdoors on the 600 x 1200mm tile, with the same wording in the suitability lines on the other two. Splashbacks are included.

The wording to hold onto is the one on the product page for your size, because the catalogue does not use the same wording across ranges. One size names the outdoors in a dedicated Area field, and the others state it in the lines about how the tile feels and looks. Check the product page of the exact size you plan to buy.

Walls and splashbacks

A wall application needs no slip rating at all, so the P4 is a floor figure. For a kitchen or laundry splashback, the 300 x 600mm tile is the smallest piece in the range. The wall tiles collection and the kitchen tiles collection list other options.

Floors

For a floor, the 600 x 600mm and 600 x 1200mm sizes give fewer joints. The recommended gap of 1.5mm to 3mm is the same for both, so the choice is visual: a square gives an even grid and the rectangle runs longer lines through a room.

Care and cleaning

The care lines are short. Maintenance is easy to clean, one size adds no sealing required, and there is zero upkeep because the tile does not need sealing or regular maintenance. The glazed porcelain surface is what makes that true.

It does not mean the tile never needs cleaning. A floor in a bathroom or an outdoor area will need ordinary cleaning like any other. The point is that you don't need to seal it first.

A real limestone floor, by contrast, needs sealing at installation and again every year or two, and porous stone near the coast is resealed every 12 to 24 months. Those schedules are for the stone, and they are not steps you need to follow for Myra.

Underfloor heating, extra tiles and batch variation

Pair these tiles with underfloor heating for a warmer, drier, mould resistant bathroom. The underfloor heating collection holds the kits.

Order extra tiles over the exact quantity, to cover breaks and offcuts during installation, because colour, size and texture can vary from batch to batch. The advice is practical for a small range. If a later order comes from a different batch, the tile can look slightly different, so it helps to have spares from the first order.

It is also sensible to keep a few spare tiles for future repairs. Because the range is a single tile, a replacement from the same batch is the closest match you will get.

Worked examples for ordering

Every Myra box covers 1.44 square metres, whichever size you choose. A bathroom floor 2.4m by 1.5m is 3.6 square metres, which becomes 4.14 square metres with 15 percent for cuts. In the 600 x 600mm tile that is 3 boxes, or 12 tiles.

A shower wall 0.9m wide and 2.1m high is 1.89 square metres, and 2.17 square metres with the allowance. In the 300 x 600mm tile that is 2 boxes, or 16 tiles. The smaller tile suits a shower, because the shorter run follows the falls and the niche edges more easily than a 600 x 1200mm tile does.

The grip finish holds a little dust in its texture. A soft brush and a mild cleaner lift it, and a mat at each door keeps most of the grit outside.

What to read before you order

The three sizes are almost identical, so a few lines separate one from another. Check these before you add to cart.

  • The dimensions and the box quantity, because the piece count changes with the size.
  • The Area or suitability line, so you know whether the tile suits indoors, outdoors or both.
  • The slip rating and whether the space is a floor, a wall or a splashback.
  • The recommended gap, which your installer will use to set the joints.
  • The appearance line and the look line, which currently print different numbers.

Myra is a plain, quiet limestone look in a small range, and the spec lines answer most questions you are likely to ask. If you want real limestone, this isn't the collection, and the natural stone pages are the better place to look. If you want a pale, matt porcelain that you don't have to seal, one tile in three sizes covers walls and floors.

Frequently Asked Questions

What is the best tile finish for a bathroom, matte or gloss?

Matte tiles are trending strongly in Australian bathrooms for their contemporary look and practical ability to hide water spots and fingerprints. Gloss tiles reflect light and can make a bathroom feel brighter and larger, but show water marks and smudges more readily. For shower recesses and wet floors, matte or satin finishes with good slip resistance are generally preferred.

How many tiles do I need to order for my bathroom?

Measure your total wall and floor surface area in square metres, then add a 10–15% wastage allowance for cuts, breakages, and future repairs. For complex layouts with diagonal patterns or feature inserts, increase the wastage to 15–20%. Always order all tiles from the same batch (check the shade lot/batch number) as tiles from different batches can vary slightly in colour.

How do I choose between floor tiles and wall tiles?

Floor tiles must have an adequate slip resistance rating (P3 minimum for domestic bathrooms) and be durable enough for foot traffic. Wall tiles can be glazed ceramic, porcelain, or natural stone, they don't need to carry load but should be moisture-resistant. Many Australian renovators choose matching or coordinating floor and wall tiles from the same range for a cohesive look.

What tile size is best for a small bathroom in Australia?

For small bathrooms, tiles between 300 x 300mm and 600 x 300mm often work well on both walls and floors. Smaller mosaic or subway tiles (75 x 150mm or 100 x 200mm) are a classic choice for shower walls. While large format tiles can also work in small spaces, they require a very level substrate and expert installation. Avoid tiles that are too small on floors (like 50 x 50mm mosaics) in large quantities, as the increased grout lines can make a space feel busier.

How do I incorporate feature tiles without over-designing the bathroom?

The most effective approach is to choose one feature zone and use your feature tile there, a full-height shower wall, the bath surround wall, or the vanity splashback area. Keep the remaining surfaces in a neutral or complementary field tile. This creates impact without visual clutter. Limit your palette to two or three complementary materials for a cohesive result.

What is the slip resistance rating I need for bathroom floor tiles?

Australian Standards (AS 4586) require bathroom floor tiles to have a minimum slip resistance rating of P3 for domestic bathrooms and P4 or P5 for wet areas like shower recesses. The Blue Space recommends checking the slip resistance rating of any tile you're considering for floor use, particularly in the shower. Matte and textured porcelain tiles generally offer better slip resistance than polished or gloss finishes.

What is the difference between ceramic and porcelain tiles?

Porcelain tiles are fired at higher temperatures and are denser, less porous, and harder than ceramic tiles. This makes porcelain more water-resistant, more durable, and suitable for both indoor and outdoor applications, including high-traffic floors. Ceramic tiles are lighter and easier to cut, making them a practical choice for bathroom walls and splashbacks. For bathroom floors and wet areas, porcelain is generally the preferred option in Australia.

What is limestone-look tile made from, and how is it different to travertine-look?

Limestone-look tile is generally a porcelain tile reproducing the finer-grained, more even texture of natural limestone, a sedimentary stone formed from compacted mineral deposits. It's a different visual character to travertine, which is also sedimentary but forms with more pitting and fossil-like surface variation. Limestone-look tends to read as a smoother, more consistent stone texture in warm neutral tones, where travertine-look leans into visible pitting and stronger veining.

What tones does the Myra limestone-look range come in?

Myra is styled around warm neutral tones consistent with natural limestone, generally sitting somewhere between a soft cream and a deeper warm grey depending on the specific colourway chosen within the range. For the exact shade options currently available, checking the range directly is the most reliable way to confirm, since a named range can span more than one tone.

Is Myra limestone-look tile suitable for a bathroom floor?

As with any limestone-look porcelain, check the slip resistance rating of the specific finish before using it on a bathroom floor. Australian Standards (AS 4586) require a minimum P3 rating for a domestic bathroom floor, rising to P4 or P5 in a shower recess or other wet area. A matte or textured finish generally performs better underfoot in a wet room than a smooth, honed-look surface.

Does Myra limestone-look tile need to be sealed like real limestone?

No. Genuine limestone is a porous natural stone that needs periodic sealing to resist staining and water damage, which matters in a bathroom or kitchen. A limestone-look porcelain tile, like the Myra range, reproduces that warm, sedimentary appearance without the porous structure, so it doesn't require sealing and holds up to everyday moisture with less ongoing maintenance than the real stone.

What style of room suits a warm neutral limestone-look tile like Myra?

The warm, understated neutral tone works well in a contemporary bathroom aiming for a calm, natural feel without the stronger veining of a marble-look or the visible pitting of a travertine-look tile. It pairs comfortably with timber or warm white vanities, and sits well with either warm metal tapware finishes or a cooler chrome or black fitting, since the tone is neutral enough to work with either direction.

How many Myra limestone-look tiles should I order?

Measure your total wall or floor area in square metres and add a wastage allowance of around 10 to 15% for cuts, breakages and future repairs, increasing to 15 to 20% for a complex layout or a room with a lot of fittings to work around. Order all tiles from the same batch or shade lot, since natural stone-look finishes can show more visible variation between production runs than a flat, single-tone tile.