Nero Kara Progressive tapware: wall sets, showers and kitchen set
Nero Kara is a brass tapware range with a round hand wheel and a slim, wall-mounted spout. In the Progressive version the water starts cold and warms as you turn the hand wheel, so one control sets both the temperature and the flow. The range is made in six finishes, which lets one design run from the basin to the bath, the shower and the kitchen.
People search for it as Nero Kara, Nero Kara Progressive, Kara tapware and Kara basin mixer. This page sets out what is in the range, the spout lengths, the water ratings and the rough-in measurements from the installation instructions, so a plumber and a tiler can plan the wall before the tap arrives.
Finishes
Kara Progressive is made in Chrome, Matte Black, Brushed Nickel, Brushed Gold, Gun Metal and Brushed Bronze. Chrome is bright and reflective. Matte Black is flat and strong against pale tiles. Brushed Nickel is a soft silver, Brushed Gold and Brushed Bronze are warm metals, and Gun Metal is a dark grey. Not every piece in the range is made in every finish, so check the finish you want against the piece you want.
| Finish | Look | Works with |
|---|---|---|
| Chrome | Bright, reflective silver | White and light tiles, any colour scheme |
| Matte Black | Flat, dark | White, grey and stone tiles |
| Brushed Nickel | Soft, satin silver | Warm greys and timber |
| Brushed Gold | Warm, soft gold | Cream, green and navy |
| Gun Metal | Dark grey metal | Charcoal and black fittings |
| Brushed Bronze | Deep, warm brown metal | Terracotta, timber and stone |
What the range includes
The range is built around wall-mounted pieces. The wall basin and bath sets are the core of it, then the shower systems and a shower mixer, and the pull out kitchen set. All are made in brass and carry the Watermark licence WM-060073. The working pressure is 150 to 500kPa, and the temperature range is 1 to 75 degrees C.
| Piece | Use | WELS | Flow |
|---|---|---|---|
| Wall basin and bath set | Wall mounted basin or bath | 5 star | 6L/min |
| Shower system, with plate or separate plate | Shower with a spout | 3 star | 8L/min |
| Shower mixer | Shower control | Set by the outlet | Set by the outlet |
| Pull out kitchen set | Kitchen sink | 6 star | 4.5L/min |
For each piece, the focused collections go further: Nero Kara Progressive wall basin and bath sets, Nero Kara Progressive shower systems and the Nero Kara Progressive collection.
Wall basin and bath sets
A wall set is a spout, a plate and a hand wheel on a body that sits inside the wall. It saves bench space, because nothing stands on the vanity, and it leaves the basin easy to wipe. It also works over a bath. The sets come in five spout lengths, and the length decides how far the water lands from the wall.
| Spout length | Exact length | WELS |
|---|---|---|
| 120mm | 120.5mm | 5 star, 6L/min |
| 160mm | 160.5mm | 5 star, 6L/min |
| 185mm | 185.5mm | 5 star, 6L/min |
| 230mm | 230.5mm | 5 star, 6L/min |
| 260mm | 255.5mm | 5 star, 6L/min |
The table gives the exact spout length for each size. Measure from the finished tile surface to the centre of the basin or the bath outlet, and choose the length that lands the water on the centre of the drain, so it neither strikes the rim nor misses the plug.
All sets are rated 5 star WELS at 6L/min.
Rough-in for the wall sets
The body must be fixed to a nogging, so the plumber needs that behind the wall before the tiles go on. The installation depth is 51 to 66mm from the nogging to the face of the ceramic tile. Then the connecting rod is adjusted so the front of the adaptor sits 25 to 28mm from the tile face.
- Fix the body to the nogging at an installation depth of 51 to 66mm from the nogging to the face of the tile.
- Connect the hot and cold hoses, take off the plastic sleeve and pressure test the body for leaks.
- Adjust the connecting rod so the depth from the front of the adaptor to the tile face is 25 to 28mm.
- Drill a 45mm hole and a 40mm hole through the plasterboard and tile for the body.
- Fit the plasterboard, waterproof the whole plasterboard, then tile, and waterproof the gap around the spout outlet.
- Remove the plastic sleeve, the grub screw and the testing plug. Fit the cartridge bell, then the plate, washer and spout, and tighten the spout grub screw with an allen key.
- Turn the hand wheel anticlockwise to the end, refit it with the C at twelve o'clock and the H at six o'clock, tighten its grub screw and press in the cap.
Shower systems
The Kara Progressive shower systems are made with a spout of 230mm or 250mm. There are two layouts. The first has a single plate that carries the hand wheel, the diverter knob and the shower outlet. The second has separate plates, so the controls and the outlet sit apart. Both have a hand shower on a bracket and a spout.
| Layout | Spout | WELS | Notes |
|---|---|---|---|
| Single plate with spout | 230mm or 250mm | 3 star, 8L/min | Plate 350mm wide and 100mm high, hand wheel and diverter knob on one plate |
| Separate plates with spout | 230mm or 250mm | 3 star, 8L/min | Hand wheel and diverter on separate plates |
| Shower system, no spout | None | 3 star, 8L/min | Single plate or separate plates |
Both systems use one universal in-wall body, and the visible part is a trim kit. The body goes in first, so the plumber installs it before the wall is lined, and the trim kit follows after tiling. See Nero showers for rails, roses and arms from the wider Nero range.
- Tile the wall, then drill holes of 20mm, 45mm, 30mm and 45mm for the body, the outlet and the controls.
- Remove the pressure test plug, then fit the cutting gauge to the mixer body so it sits flush with the tile surface, and trim any excess after assembly.
- Remove the cutting gauge and the protective sleeves.
- Set the distance between the diverter knob and the tile surface. It is 28 to 31mm for the single plate system and 25 to 28mm for the separate plate system.
- Fix the in-wall body into the wall structure so the installation depth is 51 to 66mm from the tile surface, and connect the hot and cold water lines.
- Test for leaks, then fit the plasterboard with holes of 40mm, 45mm, 40mm and 45mm.
- Waterproof the gap between the plasterboard and the mixer body.
- Thread the water outlet adapter onto the body with Teflon tape, fit the backplate, washer and shower bracket with the screws, and attach the shower hose and hand shower.
- Fit the wear-resistant O-ring, the hand wheel and the diverter knob, with the grub screws and silicone caps. Fit the washer and the spout with their grub screws. Two O-rings must be installed. Test for leaks.
Shower mixer
The Kara Progressive shower mixer is a single control with a 60mm hand wheel, for a shower that has its own outlet and rose. The body fixes to a nogging at an installation depth of 51 to 66mm from the nogging to the tile. The connecting rod is adjusted so the front of the adaptor sits 25 to 28mm from the tile. The hole through the plasterboard and the tile is 45mm. The temperature range is 1 to 75 degrees C and the pressure range is 150 to 500kPa.
Pull out kitchen set
The pull out kitchen set has a spout and a separate mixer with a 60mm hand wheel. It is rated 6 star WELS at 4.5L/min. The spout reaches 220mm, and the spout height is 226.5mm. The overall height is 423.5mm, which matters if there is a shelf or a window sill behind the sink. The pull out hose lets you reach the corners of the sink and fill a tall pot at the bench.
| Measure | Figure |
|---|---|
| Hole for the spout | 35mm |
| Hole for the mixer | 40mm |
| Counter thickness | 20 to 40mm |
| Distance between the holes | 200mm |
| Counter weight height on the hose | 350mm from the underside of the counter |
| Spout reach | 220mm |
| Overall height | 423.5mm |
To fit it, drill the two holes, then fit the spout and the mixer through them with the washers and lock nuts supplied. Join the pull out hose to the extension hose with the quick joint, and fit the counter weight onto the pull out hose at 350mm from the underside of the counter. Browse Nero kitchen taps for other Nero sink taps.
Planning the bathroom
| Decision | Check |
|---|---|
| Finish | Pick one finish for the whole room and check the piece is made in it |
| Spout length | Measure from the tile face to the centre of the basin or bath |
| Wall depth | The wall must take a body at 51 to 66mm from the tile face |
| Nogging | Fix the body to a nogging before the lining goes up |
| Shower layout | Single plate, or separate plates for controls and outlet |
| Waterproofing | Plan it with the waterproofer before the tiles |
Set out the shower and the basin positions on the wall frame before any lining. The wall sets and the shower system bodies are installed behind the tile, so they cannot be moved without opening the wall. Once the tiling is done the plumber fits the trim kits. Nero accessories are made as separate collections, such as Nero towel rails, toilet roll holders and robe hooks, so you can match the finish across the bathroom.
Cleaning
Clean every surface with mild liquid detergent or soap and water. Do not use cream cleaners or citrus based cleaning products, because they are abrasive and can damage the surface. Dry the plate and the hand wheel after cleaning, so water does not sit in the gaps.
Before you order
Confirm the finish, the spout length or the shower layout, the pressure at your supply, which must be within 150 to 500kPa, and the wall construction behind the tile. Check that the body and the trim kit are both on the order, because they work as a pair. If you are choosing between the wall sets and the shower systems, the focused collections for wall basin and bath sets and shower systems list each piece in each finish.