Skip to content

Phoenix Vivid MkII Pull Down Sink Mixers

0 Items

Whoops, there are none available in your area

View all products

Phoenix Vivid MKII pull down sink mixers buying guide


The Phoenix Vivid MKII pull down sink mixers are stainless steel kitchen mixers with a handpiece that draws out of the spout on a hose. This page holds the L shaped and the gooseneck versions, hob mounted, in stainless steel, brushed carbon, brushed gold and brushed bronze, some with a retractable head and a veggie spray. The guide below explains what a pull down mixer is, how the L shaped and the gooseneck shapes differ, why the group is stainless steel, what the cold start does, what to check under the sink and above the tap, how to choose a finish, and how to look after the mixer.

What a pull down mixer is

A pull down or pull out sink mixer has a hose inside the spout, and the end of the hose is a handpiece that sits in the tip of the spout. You draw the handpiece out and aim it, and it returns to the spout when you let go. The names pull out and pull down describe the same mixer: pull out says the head comes out of the spout, and pull down says it comes down toward the sink. The Vivid MKII is the Phoenix version, with a plain, slim body.

The handpiece is the useful part. It rinses cookware, the sides and corners of the sink, vegetables and the drainer, and it fills a bucket or a jug beside the sink, away from the spout. It reaches places a fixed spout cannot. For the wider group of this type from every brand, see pull out sink mixers, and for the other Phoenix kitchen mixers, see Phoenix kitchen mixer taps.

L shaped or gooseneck

The two shapes are the main choice. The L shaped mixer has a straight body with a spout that turns out at a right angle, in a low, clean line. It suits a kitchen with a window sill or a cabinet close above the sink, and a modern room where the tap should be a plain, quiet shape. The gooseneck has a high, arched spout, like the neck of a goose, which stands taller and gives more room under it.

Choose by the space above and below. A gooseneck suits a deep sink and a kitchen where you fill tall pots and jugs, because the arch clears them. An L shaped mixer suits a shallower sink or a low window. Measure the clearance above the sink before you choose, because a tall arch hits a low cabinet, and a short spout is awkward in a deep bowl. A strip of card at the height of the spout shows the clearance before you order. See gooseneck sink mixers for the wider group of arched spouts.

Why the group is stainless steel

Every mixer on this page is made in stainless steel. Stainless steel resists corrosion, so it suits a place that is wet most of the time, a busy kitchen and a coastal home, and it is a hard wearing metal that takes daily use without wearing through a surface layer. It is also a material that does not depend on a coating to look right, so the plain stainless finish is the metal itself.

The coloured finishes, brushed carbon, brushed gold and brushed bronze, are applied over the stainless steel body. See stainless steel tapware for the wider group. A kitchen tap supplies water you cook with and drink, so check the material and the compliance marks on the model you choose.

Cold start

The L shaped mixer has a centre lever cold start cartridge. With the lever in the centre position, the water that comes out is cold, and the hot water is brought on only when you move the lever toward the hot side. That matters in a kitchen, where the tap is used for short bursts all day: a quick rinse of a glass or the hands does not draw hot water from the heater, so the heater does not fire for a few seconds of use. Check the cold start on the model you choose, since it is a feature of the cartridge.

Spray modes and the retractable head

Many of these mixers have a handpiece with more than one function, such as a steady stream for filling and a spray for rinsing, and a veggie spray, a second spray pattern for washing produce. Some of the group have a retractable head, which draws back into the spout by itself, so the head sits flush when it is not in use. Check which of these a model has, because not every mixer in the group has all of them.

Using the handpiece day to day

The handpiece works best when it is used for the jobs a fixed spout does badly. Draw it out to rinse a large pan in the sink without lifting the pan, to wash the corners and the drainer, to fill a kettle or a bucket on the bench beside the sink, and to rinse a baby bottle or a pot that does not fit under the spout. Return it to the spout when you are finished, and let it settle into place, so the weight holds it flush.

Keep the spray head clean. Hard water leaves scale on the small holes, and a soak in a mild cleaner clears it. If the head does not return fully, check that the hose has not twisted under the sink and that nothing has been placed in its path. A handpiece that sits slightly out of the spout is the first sign that the hose is catching.

What to check under the sink

A pull down mixer needs room under the sink for the hose and the weight that returns the head. The hose has to move freely, and nothing in the cabinet should catch it: not the waste, not a bin, not a filter or a pipe. Measure the space before you order, keep the cabinet tidy once the mixer is fitted, and ask the plumber to check the path of the hose. A hose that catches stops the head returning to the spout.

Check the hole and the sink

The mixer stands on the bench or the sink deck through a single hole, so check the hole size against the tap, and the thickness of the bench, because the fixing needs enough thread under the surface. A sink with an extra hole takes a blanking plug or a soap dispenser. Check the reach against the bowl as well, so the water lands near the drain, over the middle of the bowl. See sink mixers for the wider group.

Finishes

Stainless steel is the plain, silver grey of the metal itself, and it suits a modern kitchen with stainless appliances. Brushed carbon is a deep, warm grey, close to gunmetal but softer. Brushed gold is a warm metal that suits timber, stone and cream cabinets, and brushed bronze is deeper and browner. See Phoenix brushed carbon, gold taps, Phoenix brushed bronze and bronze taps for more in each finish.

Match the finish to the other metal in the kitchen, such as the sink, the handles and the rangehood trim. If the tap comes from a different maker from the rest of the fittings, place the pieces side by side in daylight before you order, because a gold from one maker is not the same tone as a gold from another.

The Vivid MKII range

The Vivid MKII is a Phoenix range with a slim body and a clean line, and it has basin, bath and shower pieces as well as the kitchen mixers. See Phoenix Vivid MKII for the whole range, and Phoenix taps and Phoenix tapware for every Phoenix tap. A kitchen that is fitted with a Vivid MKII mixer can carry the same lines into a bathroom, and the two rooms then look related.

Water flow and installation

Taps sold in Australia carry a WELS rating for water efficiency, and it differs between models, so check the rating for the exact tap. An aerator mixes air into the stream, so it feels full and splashes less. A kitchen tap should be fitted by a licensed plumber, who connects it to the hot and cold supply, sets the hose and the weight, and checks it for leaks. The installation sheet supplied with the tap is the reference for the connection and the fixings. Give the plumber the model name and the finish before the day.

Care

Wipe the mixer with a soft cloth, mild liquid detergent or soap and water, and dry it with a soft cloth to prevent water marks. Avoid cream cleaners and citrus based cleaning products, and do not use abrasive pads, bleach or oven cleaners, because they can damage a brushed or coloured finish. Clean the aerator if the flow becomes uneven. Wipe the hose and check that the head sits back fully after use. A mixer that drips when it is shut, a lever that has become stiff or a temperature that is hard to control points to the cartridge, which a plumber can replace. Have the range name and the finish ready.

Questions to settle before you order

  • Do you want an L shaped mixer or a gooseneck?
  • How tall can the spout be before it meets a window or a cabinet?
  • Is there room under the sink for the hose, the weight and nothing to catch them?
  • Do you want a cold start, a veggie spray or a retractable head, and does the model have them?
  • Is the sink hole the right size, and is the bench thin enough for the fixing?
  • Which of the four finishes matches the sink, the handles and the rest of the kitchen?

Related pages

For the other Phoenix kitchen mixers, see Phoenix kitchen mixer taps. For the taps from every brand, start at taps.

Frequently Asked Questions

What types of kitchen sinks are available?

Australian kitchens commonly use stainless steel undermount or top-mount sinks, composite granite/quartz sinks, fireclay sinks (popular for farmhouse-style kitchens), and pressed steel enamel sinks. Stainless steel is the most popular for its durability, affordability, and hygiene. Composite stone sinks offer a premium look with good heat resistance. The Blue Space stocks kitchen sinks from Bao Bath, Turner Hastings, Seima, and other leading Australian brands.

What size kitchen sink do I need?

The right kitchen sink size depends on your benchtop width and how you use the kitchen. Single bowl sinks typically range from 400mm to 700mm wide and suit smaller kitchens or those with a dishwasher. Double bowl sinks (700–900mm) allow simultaneous washing and rinsing and are popular in larger family kitchens. Measure your cabinet opening carefully, as the sink must fit within the internal cabinet dimensions.

What should I consider when choosing a kitchen mixer finish?

The finish of your kitchen mixer should complement the other metal elements in your kitchen, cabinet handles, appliances, and rangehood trim. Chrome remains a classic, low-maintenance option that suits almost any kitchen style. Matte black has surged in popularity in contemporary Australian kitchens and pairs particularly well with dark stone benchtops and two-tone cabinetry. Brushed brass and gunmetal finishes suit warmer, more design-forward kitchens. From a practical perspective, brushed and matte finishes tend to conceal water spots and fingerprints better than polished chrome, which can show marks more readily in a busy kitchen environment.

Do kitchen mixers in Australia need to meet any standards or certifications?

Yes. All kitchen tapware sold in Australia must carry a WaterMark certification, which is a mandatory regulatory requirement confirming that the product meets Australian plumbing standards for safety and performance (AS/NZS 3718). In addition, kitchen mixers must display a WELS (Water Efficiency Labelling and Standards) rating indicating their water efficiency. A 4-star WELS rating or higher is considered good practice for kitchen mixers and will reduce water consumption with no practical performance trade-off. When purchasing online or from an importer, always verify that the product carries both a valid WaterMark licence number and a WELS label, these are legal requirements in Australia, not optional extras.