Skip to content

Radiant Floor Wastes

0 Items

Whoops, there are none available in your area

View all products

Radiant tile insert floor wastes guide


This collection holds the Radiant tile insert square floor wastes, in Brushed Satin and Matte Black, made from 316 grade stainless steel. A tile insert floor waste takes a cut piece of your floor tile in a shallow tray, so the drain reads as part of the floor and not as a separate metal plate. The two products come in two face sizes and several outlet sizes, so the first job is matching the grate to the pipe in the slab and the tile on the floor. The sections below cover how a tile insert works and what to check before ordering. For floor drains from every maker, start at floor wastes.

What a tile insert floor waste is

A tile insert floor waste has a recessed tray in place of an open grate. A piece of the floor tile is cut to fit the tray, and the water leaves through the narrow gap around the tile. The tray lifts out, which gives access to the drain beneath. The benefits are a clean look, with the drain close to invisible, and easy cleaning because the insert comes out. It must be installed with the correct floor slope and waterproofing, just like any other shower drain.

Whether a tile insert drain suits you depends on the room. A grate breaks the visual flow of a tiled floor and collects debris. An insert avoids both. The trade-off is more work at the tiling stage, because a tiler has to cut a piece to fit, and a small perimeter gap around that piece that has to stay clear. For a floor where the tile is the feature, the trade is usually worth it.

The Radiant square tile insert

The 100mm square grate with a 50mm outlet has these core measurements. The face is 100 x 100mm, the overall depth is 54mm, the insert depth is 12mm, and the material is 316 grade stainless steel in a Brushed Satin finish. The grate is designed so that tile or stone can be integrated to match the surrounding bathroom. The Matte Black version is the same square in a black finish.

The fit details matter. The 12mm deep insert accommodates up to 10mm tile and adhesive, so the tile and its adhesive together must fit in 12mm. Both products are Australian Watermark approved, and the box holds one grate. The Brushed Satin version comes in two face sizes, 150mm x 150mm and 100mm x 100mm. The Matte Black 100mm version has a 1.2mm thick base tray and a removable tile insert cover.

Outlets and pipe sizes

The outlet is a plumbing measure, and it has to match the pipe in the slab. The Brushed Satin version comes with outlets of 38mm, 50mm, 74mm and 90mm. The 90mm outlet fits a 100mm waste. The Matte Black version comes with 38mm and 74mm outlets. The 38mm variant fits a 50mm waste with a puddle flange and the 74mm variant fits an 80mm waste. Check the options on the product page for the outlet you need.

The outlet figure is smaller than the pipe size it fits. The Matte Black grate has a fixed centred outlet, 38mm to fit a 50mm waste or 74mm to fit an 80mm waste. Confirm the pipe size with the plumber or the plan before choosing the outlet.

Matching the outlet to the waste pipe

Each outlet pairs with a waste pipe size. The 50mm outlet pairs with a 50mm waste pipe, the 74mm outlet with an 80mm waste pipe, and the 90mm outlet with a 100mm waste. The 38mm version takes a waste pipe size of 40mm or 50mm, used with a puddle flange. Those pairings are the quickest check: find the waste pipe size on the plan or in the slab, then choose the outlet next to it in this list.

The puddle flange

The puddle flange is not included with a Radiant waste. The Matte Black 38mm outlet fits a 50mm waste with a puddle flange. Because the flange is sold separately, order it with the grate and match it to the waste size, and ask the plumber which flange the job needs. The point for a buyer is simple: the grate alone is not a complete drain.

Where not to put it

One restriction is easy to miss. The square grates are designed as central bathroom floor wastes and are not recommended for showers with flowing water directly above them, or directly below unrestricted overhead rain showers. Treat it as a layout rule. A specification sheet is available for each product, so a plumber or designer can check the drawings before the order goes in.

That shapes the layout. Place the grate where the floor falls to it and not under the shower rose, or choose a different drain format for a large rain shower. A linear drain, which collects along a longer line, is the usual alternative, and those are on channel wastes and grates.

Point drain, round, square or linear

Four layouts are worth comparing: an exposed point grate, a square tile insert, a round tile insert and a linear channel. The choice depends on the tile size, the fall, the waterproofing and the plumbing. A square insert suits a floor where the tile can be cut to a square and the pattern lines up with it. A round insert needs a round cut. A linear channel gives a longer drainage line and suits larger tiled areas, and large format tiles are harder to grade to a small drain.

Radiant also makes linear tile insert grates: a 900mm linear grate in 316 stainless steel, 100mm wide, with outlets such as 38mm and 74mm, and a puddle flange that is not included. The linear products are not in this collection, so look at the channel wastes page for linear drains. The square grates here are the point drain option.

316 stainless steel

Radiant floor wastes and channel drains are made from premium 316 grade stainless steel. Grade 316 outperforms 304 in resisting pitting and crevice corrosion in warm, chloride-rich environments. Both grades are austenitic, and 304 is the standard 18/8 grade, about 18 per cent chromium and 8 per cent nickel with no molybdenum. The 316 grade adds about 2 to 3 per cent molybdenum, which strongly improves resistance to pitting and crevice corrosion where chlorides are present.

Grade 304 is enough for fresh water and architectural use with little chloride exposure, and 316 is the grade for seawater, brackish water and higher chloride levels. A bathroom floor sees fresh water and cleaning products, and a coastal home or a pool surround sees more chloride, so 316 gives a margin for both. The wider choice of stainless wastes is on stainless steel wastes.

Choose 316 for an outdoor shower or a pool surround. A 316 insert costs the same effort to install as a 304 one and holds its finish longer where chlorides and cleaning chemicals are in daily contact with the metal.

Brushed satin and matte black

The two finishes suit different rooms. Brushed Satin is the stainless steel finish. Matte Black is a dark flat finish that matches matte black tapware. If the finish process matters to you, ask The Blue Space team.

A near match is the main risk with any finish. A black grate beside a matte black tap looks deliberate, while a grey grate beside a black tap can look like a mistake. Mixing metal finishes on purpose is acceptable, so a satin grate under a black mixer can also work if the room repeats the stainless tone somewhere else, such as a shower niche trim or a towel rail.

Setting out the tile

A tiler needs a few details. The base connects to the drain pipe and a frame holds a recessed tray, with the tiler cutting the floor tile to sit in the tray and leaving a perimeter gap of usually 5 to 10mm. The tray lifts out for access to the base and the trap. The 100mm and 115mm grates are the most common sizes in Australia, and a 115mm grate suits tile modules of 300 x 300mm and 600 x 600mm. The tray takes a tile cut from the same stock, so the pattern runs across the drain.

Two checks come from the Radiant numbers. The tile and adhesive together must fit within the 12mm insert, so the tile can be no thicker than 10mm. And a 100mm face means the cut piece is a little smaller than 100mm, so plan the layout of the floor tiles around the centre of the drain before the first tile is laid. Large format tiles are harder to grade to a small drain, so the grate position and the falls need planning early.

Care and cleaning

The removable insert makes cleaning straightforward. Lift the tile insert out, clear hair and debris from the tray, rinse, and refit it. For a stubborn build-up, wear gloves, flush with hot water and an enzyme cleaner, and refit the insert. Wipe the stainless steel with a soft cloth and a mild detergent, and avoid abrasive pads, which can scratch a brushed or matte finish. Rinse and dry afterwards to prevent water marks.

The trap below the floor holds a small amount of water that seals the drain against sewer gas. The seal can break through evaporation, a blockage or poor design, and hair, soap scum and poor slope are the usual causes of blockages.

How to choose

Work from the room. Confirm the pipe size in the slab and choose the outlet that fits it. Confirm the tile thickness is 10mm or less, with adhesive, and choose the face size to suit the tile module. Place the grate where the floor falls to it, away from the area directly under an overhead rain shower. Order a puddle flange to match. Then pick the finish: Brushed Satin for stainless, or Matte Black to suit black tapware. The parent page for every maker's wastes, traps and grates is wastes, traps and grates.

Frequently Asked Questions

What is a floor waste and where is it used in a bathroom?

A floor waste (also called a floor drain or shower drain) is a drainage fitting set into the bathroom floor that collects and drains excess water. In Australian bathrooms, a floor waste is mandatory in wet areas including shower recesses and is also commonly installed in the main bathroom floor area. Floor wastes prevent water damage in the event of an overflow or in wet area bathrooms designed for accessibility.

What types of floor wastes are available in Australia?

Floor wastes are available as round, square, and linear (channel) drains in a wide range of finishes including chrome, matte black, brushed nickel, and tile-insert options that allow tiles to be laid over the grate for a seamless look. Linear floor wastes (shower channels) are particularly popular in contemporary Australian bathrooms for their streamlined appearance and ease of cleaning. All floor wastes in Australia must be installed by a licensed plumber and must comply with the relevant plumbing code.

What is a radiant floor waste?

A radiant floor waste is a floor drain fitting intended for use in a bathroom or wet area fitted with underfloor heating, chosen and positioned so it works alongside the heating element rather than against it. The drainage function is the same as any floor waste, the difference is in how the installation is planned around the heating layout beneath the tiles.

Why does underfloor heating affect floor waste installation?

The heating element or cable needs to avoid running directly under or too close to the floor waste and its plumbing connection, both to protect the element from the drain's fittings and to keep the waste's fall and depth correct. This is coordinated at the design stage, before tiling, so the heating layout and the drain can share the floor without conflicting. For general underfloor heating planning, see underfloor heating.

Who should coordinate the floor waste and underfloor heating layout?

This is a job for the plumber and the heating installer working together, ideally before the screed and tiling begin. The heating layout plan should mark out the floor waste location and its required fall so the electrician or heating installer can route the element around it rather than discovering a clash after the cable is laid.

Does a radiant floor waste need a different fall or gradient to a standard one?

The fall requirement, a slight slope in the floor directing water to the drain, is the same underlying principle as any floor waste. What changes with underfloor heating is that the screed depth and heating cable position both need to be accounted for when the fall is set, since the tiler is now working around an additional layer in the floor buildup.

Can any floor waste be used with underfloor heating, or does it need to be a specific type?

In principle a standard floor waste can be used, provided its position and depth are planned around the heating layout from the start. The practical difference is in the installation sequence and coordination between trades rather than a special drain type being mandatory, though checking manufacturer guidance for both products is worthwhile before finalising a design.

Should the floor waste or the heating layout be planned first?

The floor waste position is generally fixed early, since it depends on the room's fall and existing plumbing stack location, and the heating element is then laid out to avoid it. Trying to retrofit a floor waste around an already-installed heating layout is far more disruptive, so this sequencing is worth confirming with your plumber and heating installer before either trade starts work.