Turner Hastings Narva: MagnaCast baths and basins
Turner Hastings Narva is a modern bathroom range built around MagnaCast mineral composite, a dense, handmade-in-Europe material that holds heat well and has a smooth, non-porous surface. It covers a 1580mm back to wall bath, a 1600mm freestanding bath, a 600mm MagnaCast bench basin and a ceramic undercounter pill basin. The baths come in gloss white and matte white, and the pill basin comes in gloss white, matte white and matte black.
People search for it as Turner Hastings Narva and Turner Hastings basins. This page sets out each piece with its size, weight and waste, and the planning that matters before a heavy bath arrives. For every Turner Hastings bath, see Turner Hastings baths, and for every basin, see Turner Hastings basins.
What is in the Narva range
| Group | Pieces | Where to see more |
|---|---|---|
| Baths | 1580mm MagnaCast back to wall bath; 1600mm MagnaCast freestanding bath | Turner Hastings MagnaCast baths |
| Basins | 600mm MagnaCast bench basin; 57 x 39 undercounter pill basin | Turner Hastings basins |
MagnaCast material
MagnaCast is a mineral composite that is non-porous and impact resistant, so water and stains do not soak in and the surface wipes clean. It has good heat retention properties, which keeps bath water warm for longer, and it is handmade in Europe. The baths weigh 150kg empty, which is heavy, and that weight is part of the planning. The material is solid, so the bath feels substantial and stays stable, but the floor and the route into the room must be ready for it.
The Narva baths
| Bath | Length | Width | Height | Inner depth | Capacity | Weight |
|---|---|---|---|---|---|---|
| Back to wall | 1580mm | 860mm | 590mm | 430mm | 417L | 150kg |
| Freestanding | 1569mm | 740mm | 600mm | 451mm | 377L | 150kg |
The back to wall bath sits flush to one wall, so there is no gap behind it to clean, and at 860mm wide it is a roomy bath. The freestanding bath is narrower at 740mm and is finished on every side, so it needs room around it. Both baths have a centre waste. The standard versions have no overflow and need a 40mm waste without an overflow, which is sold separately. A gloss white freestanding version is also made with an overflow, so read the product page for the one you want before you order the waste.
The bath depth is where comfort sits. The back to wall bath has a 430mm inner depth and the freestanding bath has 451mm. Both are close to the 450mm to 480mm that suits a good soak. Compare the inner depth between baths, and ignore the overall height, which includes the rim and the base. See freestanding baths and back to wall baths for other makes.
Floor load and clearance
A freestanding bath puts its weight on a few small feet. Water adds about 1kg per litre, so the load with a bather can reach 400kg to 500kg, and a timber floor usually needs reinforcement, such as blocking between the joists. Leave 200mm to 300mm clear on three sides and 600mm at the entry end, with 50mm to 100mm around the bath for cleaning. A freestanding bath is at its best in a bathroom 2.8m wide or more, and a back to wall bath suits a narrower room.
The MagnaCast basin
The 600mm MagnaCast basin is a bench basin, 600mm long, 350mm wide and 166mm high, with a 125mm bowl depth and a 13 litre capacity. It stands 150mm above the benchtop, so the tap must clear it. It has no tap hole, so a bench mounted or wall mounted tap suits it, and it has no overflow, so the waste must be a type without one. A MagnaCast free-flowing waste cap is supplied, which gives a clean look if you prefer not to plug the waste, and the basin also suits a universal 32mm or 40mm two piece brass pop-up waste.
The undercounter pill basin
The 57 x 39 undercounter pill basin is ceramic in a soft pill shape. It is 570mm long, 390mm wide and 210mm high overall, with an inner size of 510mm by 325mm and an inner depth of 200mm. It has no tap hole and it includes an overflow, so it needs a 32mm waste with an overflow, sold separately. The overflow is glazed, and it suits a large brushed brass or matte black overflow ring if you want to match your tapware. It is made in gloss white, matte white and matte black.
| Basin | Size | Depth | Overflow | Tap holes |
|---|---|---|---|---|
| 600mm MagnaCast bench basin | 600mm by 350mm | 125mm bowl, 150mm above the bench | None | None |
| 57 x 39 undercounter pill basin | 570mm by 390mm | 200mm inner depth | Included, glazed | None |
An undercounter basin sits under the benchtop, so the bench edge runs clean into the bowl, which suits a stone or solid surface top. The cut-out in the bench must be accurate, and the tap goes on the bench behind the basin or on the wall. Because there is no tap hole in either basin, the tap decision comes first. See basin wastes for wastes that suit a basin with or without an overflow.
Waste and overflow
The overflow line decides which waste you need. A bath or basin with an overflow takes a waste made for an overflow, and a non-overflow piece takes a waste without one. The Narva baths without an overflow need a 40mm waste, the MagnaCast basin needs a non-overflow basin waste, and the pill basin needs a 32mm waste with an overflow. Australian building codes require a fully removable bath waste in some situations, so ask your plumber before you buy. See bath wastes for options.
Planning the wall
Wall mixers, wall taps and spouts go into the wall before the tiles, so settle the position, the spout reach and the finish while the wall is open. Measure from the finished tile surface to the centre of the drain to choose the reach, so the water lands in the middle of the basin or the bath outlet and clears the rim. Check what sits behind the wall, and fix the body to a nogging or a bracket so it holds. Waterproofing behind the body matters, because a missed seal is a leak inside the wall that cannot be fixed without opening the tiles.
Where the pipes go
Water reaches a bath by one of two routes. A floor mounted mixer takes its pipes up through the floor, and a wall mounted spout takes them through a wall. Floor flanges should be fixed to the structural floor, not just to the tile, and the supply pipes should be pressure tested before the floor finish goes on. A floor mounted spout needs precise positioning before tiling, which is why the tapware is chosen before the bath is fixed. Confirm the position matches the tap you chose, because changing it after delivery is costly.
Tapware for a bath
A freestanding bath needs a floor mounted spout or mixer, or a wall mounted set if the bath sits close enough to a wall. Leave at least 100mm clear around the bath edge for a freestanding mixer. A wall mounted spout with a long reach can work if the bath is positioned close enough, and a bath near a wall can need a spout arm of nearly 350mm, so check the reach before you fix the position. A back to wall bath takes a wall mixer and a spout, or a deck mixer where the bath has a tap deck.
Caring for the bath
Rinse the bath after each use, then wipe it with a soft sponge or a microfibre cloth and a pH neutral cleaner. Avoid bleach, ammonia, abrasive powders and steel wool, which dull the surface. Give the bath a weekly deeper clean and a monthly look at the waste and the silicone seals. A freestanding bath has more surface to dry, so a quick wipe of the sides after use keeps soap marks from setting.
Choosing the waste
A slotted waste is used with a basin that has an internal overflow, and an unslotted waste where there is none, so check the overflow before you order. Most basins need the waste bought separately so it can match the tapware. Chrome, black and brushed finishes, and mushroom or button pop-up styles, are the usual choices. Choose the waste when you choose the tap, so the metals match.
One tap hole or three
A one hole basin takes a single mixer on the bowl. A three hole basin takes a spout in the middle with the hot and cold controls on either side, which is the traditional layout. A basin with no tap hole takes a wall mixer or a bench tap behind the bowl. Hole spacing varies by manufacturer, so check the tap against the basin before you buy, especially if you already own a tap set you want to keep.
Planning a Narva bathroom
Start with the bath, because it is the largest and heaviest piece. Settle the format, the waste position and the floor strength first. Then choose the basin and the tap for it, and match the finish of the tapware to the room. Matte white suits a soft, plain bathroom, gloss white is brighter, and a matte black pill basin gives a strong contrast against pale tiles and a white bath.
Before you order
Confirm the bath format and the waste, and whether the bath has an overflow. Check the floor under the bath and the route into the room for a 150kg piece. For a basin, confirm the tap hole and the overflow and choose the waste to suit. Choose the finish across the bath and the basin so the set reads as one.