Zanda Duke entrance set buying guide
The Zanda Duke entrance set is a complete front door set: a pair of Duke levers, a Euro mortice lock, matching escutcheons and a 70mm double cylinder that takes a key from both sides. The Duke lever has soft curves and an easy grip, and it is sold here in four finishes: brushed nickel, Ember Bronze, white and matte black. This guide explains what is in the box, how the four finishes differ, what the fitting system does, how to match the set to your door, and how to look after it. For the wider Duke family, including internal sets and pull handles, see Zanda Duke door hardware, and for entry sets from every range, see entrance door hardware.
What is in the set
Each set is made for one door. The box holds the Duke lever pair, a 1143 E85 mortice lock, a matching pair of escutcheons and a 70mm key/key double cylinder, with a fixing kit and installation instructions. The levers are zinc alloy. The lever is 116mm long, and it sits on a 54mm screw-on rose with concealed fixings, so no screw heads show on the face.
The lock is a Euro mortice lock with a tubular bolt latch and a 60mm backset. The cylinder is keyed different, so each set comes with its own keys and will not share a key with another Duke set unless you have a locksmith re-key it.
The four finishes
| Finish | Coating | Door thickness | Where it suits |
|---|---|---|---|
| Brushed nickel | Electroplated | 35 to 53mm | Coastal and light schemes, timber or white doors |
| Ember Bronze | Electroplated | 35 to 45mm | Warm schemes, dark timber, deep green or charcoal doors |
| White | Powder coated | 35 to 53mm | White doors, pale frames, a quiet modern look |
| Matte black | Electroplated | 35 to 53mm | Japandi and Australian modern entries, black frames |
The door thickness range is the one number that changes between the finishes. The brushed nickel, white and matte black sets suit doors from 35 to 53mm thick. The Ember Bronze set suits doors from 35 to 45mm thick, so measure the door before you choose that finish.
The lever
The Duke lever has soft curves and an ergonomic shape. It is 116mm long, a compact lever that is easy to use for most hands and does not stick far out into a hallway. The rounded profile suits a modern house and sits quietly against a traditional door too, which is why the Duke is used in coastal homes, Japandi interiors and Australian modern designs. Compared with the Cambridge, which is a classic curved lever, the Duke is plainer and more contemporary. The Cambridge sets are on Zanda Cambridge door hardware.
RapidFIT and through door bolts
The Duke uses RapidFIT technology, a fitting system designed to make installation faster. The set also uses through door bolts, which pass through the door and hold the lever and rose firmly. Through bolts stop the handle twisting out of square over time, which is a common reason for a lever to loosen on a busy front door.
The rose is a 54mm screw-on rose with concealed fixing, so once the set is on the door the surface is clean. The finish is made to resist corrosion over time if it is cared for, so a gentle clean now and then is part of the deal.
Why a double cylinder
The cylinder is a double cylinder, key/key. A double cylinder needs a key from both sides. It is a strong choice for a door with a glass panel beside it or in it, because a person cannot reach through broken glass and turn a knob. It also means the key is needed to leave when the door is locked. Keep a spare key in a fixed place near the door, out of sight from outside, and make sure everyone in the house knows where it is. If the door is an exit in a rental, a business or an apartment building, check the exit rules with the building manager before you choose key on both sides.
The 70mm cylinder and the escutcheons
The 70mm cylinder is matched to the escutcheons and to the door thickness in the table above. The cylinder has to be long enough to reach both escutcheons and not so long that it stands proud. If your door is at the thin end of the range, check how the cylinder sits against the plates before you fit the lever. A 60mm cylinder is a different part and is on other Zanda sets.
Which finish for which door
Match the finish to the door colour and the other metal on the house.
Brushed nickel is a soft silver, calm against white, grey and timber, and it hides fingerprints better than polished chrome. Ember Bronze is a deep, warm brown that works with timber, dark paint and brick. White is a powder coat that disappears on a white door and frame, which suits a minimal entry with no obvious hardware. Matte black is the strongest contrast. It suits a pale door, a black framed glazed door or a Japandi interior with timber and black accents. For a wider choice of black and white hardware, see matte black door handles and white door handles. For the bronze family, see Zanda Ember Bronze door hardware.
Fitting a set
A fitter or a handy owner can fit a set in these steps.
- Check the door thickness, the 60mm backset and the mortice pocket for the lock body.
- Fit the lock body into the mortice and fix it at the door edge.
- Fit the cylinder, then the escutcheons.
- Fit the lever and rose with the through door bolts, and tighten them evenly.
- Fit the strike in the frame and test the key and the lever with the door open.
The instructions in the box set out the screw lengths for each part. A door that is not prepared for a Euro mortice lock will need a mortice cut first, and a joiner can do that.
Where an entrance set is used
The obvious place is the front door, but the set suits any external door that needs a lock and a lever: a side entry, a back door, a garage access door or a studio at the end of the garden. On a pair of doors, fit the set on the active leaf and use bolts on the other. Because the set has a key on both sides, it suits a door with sidelights or glass in the leaf, where a turn knob would sit within reach of a thief. If the door only needs a latch with no lock, an internal passage set is the better choice.
Replacing an existing set
When you replace an old set, measure before you order. Check the backset, which is 60mm on this lock, the door thickness, and the size of the old rose. The Duke rose is 54mm across. An old rose that is larger leaves a ring on the paint that the new rose does not cover, so allow for a touch-up. Check that the existing mortice pocket is the right size for the 1143 E85 lock body, and that the cylinder hole suits a Euro profile cylinder. If the old lock was a different type, the door will need a new pocket.
Powder coat or electroplate
Three of the four finishes are electroplated and the white set is powder coated. Electroplating bonds a thin metal layer to the lever and gives a finish that reads as real metal. Powder coating is a baked paint layer, and it gives a solid, even colour that matches a white door. Both wear well with care. A sharp knock can chip a powder coat, and abrasive cleaners wear electroplate, so treat both gently. On a door that gets a lot of use, wipe the levers with a soft cloth every week or two.
Matching the metal around the entry
An entry carries more metal than most doors: the lever, the hinges, a letterbox, house numbers, a doorbell and sometimes a light. Keep that to one or two finishes. If the lever is matte black, black hinges and a black letterbox look settled. If the lever is brushed nickel, a nickel stop and nickel hinges keep the door consistent. If the lever is Ember Bronze, a bronze stop works well with dark timber. The window frames beside the door set the scheme as well, so match the set to the frame colour when the door and the windows are close together.
Questions people ask
Can the lever be used outside in the weather? Yes. The set is made for external doors, and the finish is made to resist corrosion if it is cared for. Does the set fit a standard door? It suits doors 35 to 53mm thick, or 35 to 45mm in Ember Bronze, with a 60mm backset and a prepared mortice. Does it need a separate lock? No. The mortice lock and the cylinder are in the set. Can I fit it myself? A competent person can, if the door is prepared. If it is not, a joiner should cut the mortice first.
Care
Wipe the levers and the escutcheons with a soft damp cloth and dry them. Avoid abrasive pads and strong cleaners, which damage electroplated and powder coated finishes alike. On a white or black set, wipe off marks soon after they appear, since they are most visible on those finishes. Near the coast, rinse off salt with fresh water.
Matching the rest of the door
Pair the set with matching hinges and a stop in the same finish. Zanda hinges are on Zanda hinges, and stops are on door stops. If you want a pull handle on a second leaf or a side door, the Duke family has matching bars on Zanda Duke pull handles. For extra security beside the lever, a separate deadbolt is on deadbolts.
Common mistakes
Check these before you order and again before you drill.
- Ordering the Ember Bronze set for a door thicker than 45mm.
- Choosing a double cylinder for a door that is a required exit.
- Assuming a new set will use the old door preparation without checking the mortice pocket and the backset.
- Mixing a black lever with nickel hinges.
- Leaving the through bolts loose, so the rose moves on a busy door.
Our recommendation
Choose the Duke entrance set when you want a modern, softly curved lever and a complete front door set in one box. Take brushed nickel for coastal and light schemes, Ember Bronze for warm ones, white for a minimal entry and matte black for contrast. Measure the thickness, check the backset and the mortice, and keep a spare key near the door.