1500mm Vanities Buying Guide
A 1500mm vanity is the width where a bathroom starts to feel generous. It is long enough for two bowls with a clear stretch of bench between them, and long enough to look deliberate on a single wide top. The width is only the start, though. The bowl layout, the depth, the way the cabinet mounts and what the plumbing does behind it decide whether a 1500mm vanity works in your room. This guide takes those choices in the order you will make them.
Who a 1500mm vanity suits
The usual home for a 1500mm vanity is a shared bathroom or a main ensuite, where two people use the room at the same time. It is the smallest width at which two bowls sit comfortably side by side, with room for a tap, a toothbrush and an elbow at each one. A single bowl on a 1500mm top is the other way to use the width, and it suits one person who wants a long run of clear bench for a hairdryer, a tray and a plant.
If the two-basin decision is still open, the double vanity collection sets out the trade-offs in more detail. If 1500mm feels too long for the wall, the 1200mm vanities are the step down, and the 1800mm vanities are the step up.
How much wall it needs
A vanity needs its own width plus a margin at each end, so a 1500mm vanity wants a wall of about 1600mm. That allows roughly 50mm between each end of the cabinet and the nearest wall, shower screen or fixture, which is enough for the doors and drawers to open without catching and enough for a bead of silicone to sit cleanly. Measure the wall at floor level and again at bench height, and use the smaller figure, because walls are rarely the same length at both. If the number is tight, a vanity that stops 100mm short of the wall looks deliberate, and one jammed wall to wall looks like a mistake.
Basin layouts at 1500mm
At 1500mm the double bowl is the most common layout, and centre, offset, left and right single bowls are also offered. A centre bowl puts one basin in the middle of the top, with equal bench on each side. An offset, left or right bowl pushes it to one side and leaves a long clear run of bench on the other, which suits a room where one end of the vanity is close to a door or a screen.
A double bowl needs two sets of connections: two water supplies, two wastes and two traps. Confirm the layout before you plan the pipes, because the position of each bowl sets where the plumber drills the cabinet. Check the drawing for the distance between the two bowl centres and for the bench left at each end. Each bowl needs enough bench beside it to be useful, and a basin that sits too close to the end of the top leaves nowhere for a soap dish.
A single bowl on a wide top, or a double
Check what is included
A vanity can be sold as a cabinet only, a cabinet with a top, or a cabinet with a top and basin, and the waste and tapware are usually separate. Check the inclusions on the product page before you compare two units at the same width. For a cabinet without a basin, choose one from the bathroom basins made to suit the top.
The tap hole position is set when the top is made, so choose your tapware first, or confirm the tap hole count, before you order. Most ceramic tops take one tap hole for a basin mixer, a top with no tap hole is for wall-mounted tapware, and some ranges let you choose none, one or three holes. A double needs a tap for each bowl. Browse taps and mixers by type to settle the tapware before the top.
Depth and clearance
Standard vanity depth is about 450mm to 500mm, and slimline units are shallower, at roughly 320mm to 400mm. Compact depth units are offered at 1500mm, so check the depth on the product when floor space is tight. A shallower unit gives up some storage and usually takes a smaller basin, so choose it for the walkway you gain, not for the look. Measure depth from the finished wall to the front edge of the basin, because that is the distance you will stand in front of.
Wall hung or floor standing
A wall hung 1500mm vanity leaves the floor visible beneath the cabinet, makes cleaning underneath easier and makes a room look larger. It needs solid fixing in the wall and the waste coming out through the wall, which is easiest to arrange while the walls are open, so decide early in a renovation. A floor standing vanity carries its weight on the floor and can cover floor pipes, so the wall fixing is lighter and it suits a room with finished walls.
See wall hung vanities and freestanding vanities for the wider range in each style, and the bathroom vanity guide for the two side by side.
Supporting a long wall hung cabinet
A 1500mm wall hung vanity carries two bowls and a stone or ceramic top, so the wall behind it has to be planned. Fit a support beam or noggin between the studs before the wall is lined. The noggin must be wider than the vanity, so on a 1500mm cabinet it runs the full length of the cabinet and a little beyond, and the cabinet is fixed through the back, at the top and bottom, into at least two studs or noggins. Keep the horizontal fixings no more than 300mm apart, which means several fixing points along a cabinet this long.
Floor standing at 1500mm
Plumbing for two bowls
All plumbing work must be done by a licensed plumber, who can confirm the pipe positions against the inside of the cabinet before the vanity is fixed. The waste may come through the wall or the floor, and a double bowl means two of each. The holes for the pipes are drilled in the back panel or base with a hole saw, so a wide cabinet with two sets of holes needs the positions measured carefully. Give the plumber the product drawing early, before the pipes are set, and check the clearance behind the drawers where the water supply fittings sit.
Drawers, doors or both
Drawers are the most common layout at 1500mm, many units combine doors and drawers, and doors only is the rarest. Drawers show everything at once and can be cut around the waste, so a drawer under a basin holds less than its width suggests. Doors leave a taller open space for bulky items such as spare toilet rolls and cleaning bottles. A mix gives you both, and on a cabinet this wide it often makes sense to have drawers at the bowls and a door section between or beside them.
Getting a long cabinet into the house
Tops and basins
An inset basin drops into a cut-out so the rim sits flush with the bench. An above-counter basin sits on top like a bowl, which shows off its shape and frees up cabinet space beneath. An undermount basin is fixed under the top, so you can wipe water straight off the bench into the bowl and keep the most bench space. At 1500mm, where there may be two bowls, the undermount or integrated option keeps the line of the bench clean.
Finishes and styles
The range comes in white, woodgrain, black and grey, and many products come in more than one finish. The most common design styles are Japandi, Coastal and Mid Century Modern. For natural timber, see solid timber vanities, and for the lightest finish, white bathroom vanities. Fluted and curved fronts add texture and softer edges, and Hamptons vanities suit a classic room.
Mirror and lighting
A 1500mm vanity can take one wide mirror or one mirror over each bowl. One wide mirror gives one clean line across the wall, and two mirrors mark out a zone for each person. As a guide, a mirror about 50mm to 100mm narrower than the vanity, set in from each side, looks balanced, and it should hang about 100mm to 200mm above the bench or the basin rim so it clears the tap handles. See mirrors. Plan the lighting at the same time, with a light for each bowl, because the light and power point positions depend on the mirror and the vanity width.
Tiling, sealing and care
Tiles should run behind and beneath the furniture, and tiling in around it is not recommended, because moisture and mould can build up and damage the material. The cabinet materials are moisture resistant, not waterproof, so keep the vanity at least 300mm from wet areas such as a bath and out of shower spray. Seal every edge where the cabinet or top meets the wall or floor with a continuous bead of neutral cure silicone, and make sure the room is well ventilated.
For care, a soft cloth and a weak solution of non-abrasive detergent suit the cabinet, and any water spilled on or inside it should be dried. Ceramic tops and basins want the same cloth and detergent, and a scratch in glazed ceramic cannot be repaired, so avoid scourers. With two bowls there are two sets of tap and waste seals to look over about once a month, and cracked or lifting silicone should be redone straight away, because that is how water gets into the cabinet.
Built to order and timing
Most vanities in this collection are built to your choice of size, top or finish, and many are Australian made. A unit built for you takes longer to arrive than one taken off a shelf, so confirm the arrival date on the product page before you book trades. Compare the full inclusions rather than the headline figure, because the top, the finish and how the unit is made change what you get. For a one-off size, see custom vanities.
Compare nearby sizes
If 1500mm is close but not right, compare the 1200mm and 1800mm collections, or browse vanities from 1000mm to 1800mm in one place. For a tight room, small vanities is the better filter.
Completing the room
Shop by brand
Browse 1500mm vanities by brand: Timberline, Marquis, ADP, Otti, Ingrain and BelBagno.