Skip to content

Oak Ceiling Fans

0 Items

Whoops, there are none available in your area

View all products

Oak ceiling fans buying guide


An oak ceiling fan is a fan with a pale, natural timber look, usually paired with a white body. People searching for oak, timber or wooden ceiling fans are often asking one question first: is it real wood, and is a wooden fan any good? On every fan in this collection the blade material is ABS plastic or aluminium, so the oak is a finish and not solid timber. This guide explains what that means and how the oak fans compare. It then goes through size, light, motor and ceiling, and finishes with installation and care.

Is an oak ceiling fan real oak?

Not here. Many blades that look like wood are plastic, and the specification of each fan in this collection gives the blade material. The Eglo Seacliff has UV-resistant ABS blades in a white and oak finish. The Eglo Surf in oak and white has UV-resistant ABS blades and body on the 52 and 60 inch sizes, and aluminium blades on a steel body on the 40 and 72 inch sizes. The Martec Avoca, Metro, Newport and Hampton pair a matt white body with oak-finish blades, and all four are built from steel and ABS. If the material matters to you, the blade line is the one to read, and a timber-look fan that does not state it is worth questioning.

One note for sunny rooms: standard ABS can become brittle or yellow with prolonged heat and UV exposure unless it is UV-stabilised. The Seacliff and Surf have UV resistant ABS. A fan in direct, prolonged sun is the situation to avoid.

Choosing an oak fan for the look

Oak is a light timber tone. A natural or light timber finish suits lighter spaces, and it belongs in modern, coastal, Scandinavian and minimalist interiors. The oak-and-white combination on these fans keeps the body pale, so the fan blends into a white or light ceiling while the blades bring a natural note. White blends into a light ceiling and suits modern and traditional decor, and black contrasts. Check the oak tone against other timbers in the room, such as a floor, a table or cabinetry, because mismatched wood tones can clash. Colour makes no difference to how much air a fan moves.

For other finishes see woodgrain ceiling fans, walnut ceiling fans and bamboo ceiling fans, and for body colours white ceiling fans.

The oak fans in this collection

  • Eglo Seacliff, 44 and 52 inch, white with an oak finish: DC, 16 watts on the 44 inch and 28 watts on the 52 inch, six speeds, three UV-resistant ABS blades, a steel low profile canopy, a drop of 234mm and flat ceilings only. It is for indoor locations around the home. The lit versions have a 15 watt LED of 1,750 lumens that switches between 3000K and 5000K, with 4000K in between.
  • Eglo Surf, oak and white, in 40, 52, 60 and 72 inch: DC. The 52 and 60 inch have ABS blades, a 40 watt motor, airflow of 13,743 and 14,194 cubic metres an hour, and an application line of indoors or covered outdoor areas not exposed to the weather. The 40 and 72 inch have aluminium blades and draw 30 and 58 watts. They stand about 293mm to 297mm overall, take 15 degrees of ceiling pitch and are for indoor use.
  • Martec Avoca, 1220mm and 52 inch Smart: DC and 45 watts, built from steel and ABS, with 15 degrees of pitch. It has Wi-Fi control, and the light version gives 2,500 lumens.
  • Martec Metro, 1320mm: a hugger fan of 33 watts with an overall height of 210mm to 220mm and 0 degrees of pitch, so a flat ceiling only, with a 1,885 lumen light version.
  • Martec Newport, 1420mm: DC, 39 watts, 10 degrees, six speeds plus sleep and breeze modes, and a light of up to 2,500 lumens.
  • Martec Hampton, 1320mm: DC, 40 watts, 10 degrees, an overall height of 295mm.

The Martec ranges each have their own page: Avoca and Metro, Newport and Hampton.

Choosing the size

A 52 inch (132cm) fan is the standard size, 48 inch (122cm) suits smaller rooms and over 54 inch (137cm) suits larger square rooms of about 5 by 5 metres or more. By area, 6 to 12 square metres takes 48 to 52 inch, 12 to 20 square metres takes 52 to 60 inch, and over 20 square metres takes 60 inch and larger. The 40 inch Surf and 44 inch Seacliff suit a small room. The Avoca and the 52 inch fans suit a bedroom or standard living room, and a larger room takes the 60 and 72 inch Surf or the 1420mm Newport. A long room does better with several 52 inch fans than one very large fan.

Ceiling height and pitch

Blades must hang at least 2.1 metres above the floor, and at least 300mm from the ceiling for Martec fans. The heights range from 210mm on the Metro and 234mm on the Seacliff to about 293mm to 297mm on the Surf and 331mm on the lit Avoca. On a 2.4 metre ceiling, the Metro leaves the blades at about 2.18 metres and the lit Avoca at about 2.07 metres, which is under the minimum, so the Avoca with a light suits a higher ceiling. These figures are arithmetic from the heights, and the electrician should confirm them. The Metro and Seacliff are 0 degrees of ceiling pitch, so they need a flat ceiling. The others take 10 or 15 degrees. Fans generally handle about 10 degrees of tilt without a kit. See low profile fans and ceiling fans for high ceilings.

With a light or without

Most oak fans come with and without a light. The lit versions give 1,750 lumens on the Seacliff, 1,885 on the Metro, 2,500 on the Avoca and up to 2,500 on the Newport. Warm white of about 2700K to 3000K suits bedrooms and lounges and neutral white of about 4000K suits task rooms. A fan near downlights can strobe as the blades pass in front of them and many models are sold as light or no-light versions only. A light adds height, so check the figure for the version you buy. See ceiling fans with lights and ceiling fans without lights.

Are 3 or 4 blades better?

Blade count is not a factor. There is no performance difference between 3 and 4 blade fans, and tested models range from 2 blades up to 5. Fewer blades move air faster and more blades are often quieter. All of the oak fans with a stated blade count have three blades, so the question does not arise within the collection, and judging by the airflow figure and the size is the better route.

Motor, speeds and controls

Every oak fan here is DC. DC motors tend to be quieter and offer more speed settings, work on a household supply through an internal rectifier, and are generally more efficient than AC. The Seacliff and Surf have six speeds, the Newport six speeds plus sleep and breeze modes, and the Avoca eight settings or five speeds with a timer depending on the line. Each comes with a remote. See DC motor fans and smart ceiling fans.

Where an oak fan can go

Most of the oak fans are for indoor use. The 52 and 60 inch Surf suit indoors or covered outdoor areas not exposed to the weather, and so does the Avoca Smart. Covered does not mean fully dry. Wind-driven rain and sea air can reach a fan near the edge of a roof, and so can mist, and timber-look blades suit indoor rooms. For outdoor placement see outdoor ceiling fans.

Installation and care

A ceiling fan is a fixed electrical appliance, and hard-wired fans must be installed by a licensed electrician. Fitting a wall-switch fan without a licence is illegal. Wipe the blades every few weeks, and check the care notes before using a cleaner. A fan that wobbles is louder and less efficient, and a balance kit corrects it. Have the fan inspected early if it hums, wobbles or runs slowly.

Noise and balance

A quiet fan matters most in a bedroom, so listen at the lowest speed. Clicking or knocking is more irritating than steady air noise. Humming can come from ripple control signals on the supply and is usually not a fan fault, and a conventional dimmer on a fan light can also cause humming. Wood is heavier than plastic, and real timber blades run quietly. The oak fans here have ABS or aluminium blades, so judge the noise on the motor type and the speed setting. A DC motor is the quieter choice.

Extension rods and high ceilings

Ceiling heights of 2.1 to 2.4 metres give the best performance. On ceilings of about 2.7 to 3 metres or higher, a fan may need an extension rod, which is sometimes included, sometimes sold separately and not available for every model. Mount the fan 2.3 to 2.7 metres above the floor. For a high ceiling see ceiling fans for high ceilings. A hugger fan such as the Metro is the reverse case, built to sit close to a low ceiling and keep the blades clear of heads.

Short answers on oak fans

  • Is the oak real timber? No. The listed blade material is ABS or aluminium with an oak finish.
  • Can I use an oak fan in a bathroom? Timber suits rooms with stable humidity, and a fan with no damp rating does not suit a bathroom. Extraction is a separate job, see bathroom exhaust fans.
  • Will the finish fade in sun? UV-stabilised ABS resists fading and cracking. The Seacliff and Surf have UV resistant ABS.
  • Does the oak finish move less air than white? Colour does not affect airflow. Blade shape and motor do.
  • Does it come with a remote? Remote control comes with these fans, so check the version you are buying.

Related collections

For every style see ceiling fans. By brand, Martec ceiling fans.

Frequently Asked Questions

What's the difference between oak ceiling fan blades and timber-look blades?

Genuine oak blades are made from real timber veneer or solid oak, giving natural grain variation where no two blades look exactly alike. Timber-look blades are typically ABS plastic or MDF finished with a printed or laminated timber grain pattern, giving a consistent, uniform look across every blade. Timber-look is usually lighter, more affordable and more moisture-tolerant, while genuine oak gives a more authentic finish and texture at a higher price point.

Do oak or timber-look ceiling fan blades need different care to standard fan blades?

Genuine timber blades benefit from a dry dust or wipe rather than a wet cloth, since excess moisture can affect the timber or its sealant over time, and they're better suited to indoor rooms with stable humidity rather than a bathroom or exposed outdoor area. Timber-look composite blades handle a light damp wipe without concern, since the timber grain is a printed finish over a moisture-stable material rather than actual wood. Check which type your fan uses before deciding how to clean it.

Will an oak ceiling fan suit any interior style, or is it better for a particular look?

Oak and other timber finishes tend to suit warmer, more traditional or Scandinavian-influenced interiors, and pair naturally with timber flooring, exposed beams or wood furniture elsewhere in the room. In a strongly monochrome or industrial-style space, a metal or matte black fan will generally sit more consistently with the rest of the palette than a timber blade will. It comes down to matching the fan to the room's existing materials rather than one finish suiting every style.

Are oak ceiling fan blades heavier than standard ABS or metal blades?

Genuine timber blades are generally heavier than ABS plastic blades of the same size, though usually lighter than solid metal blades. Blade weight affects momentum and how a fan feels when running, heavier blades can carry through rotation more smoothly at low speeds, but it also means the motor and mounting need to be rated to handle that extra weight, which manufacturers account for in their design rather than something to check separately.

Can oak ceiling fans be used outdoors?

Genuine timber blades are generally not suited to outdoor use, since direct weather exposure and humidity swings can cause warping, splitting or finish deterioration over time in a way that purpose-built outdoor materials are designed to resist. If you want a timber look in an outdoor or alfresco area, look for a fan specifically rated for outdoor use with weather-resistant composite blades finished to resemble timber, rather than genuine oak. See outdoor fans for options built for that environment.

Do oak ceiling fans come with a light option?

Many do, though availability varies more by individual model than by the timber finish itself. An integrated light kit works the same way regardless of blade material, so if a light is a priority, check that specific feature on the individual fan rather than assuming every oak or timber-finish fan includes one.