Taps buying guide
Taps are the fittings you use most in a bathroom, kitchen or laundry, so the choice is worth making with a plan. This page is the starting point for every tap we sell. It covers the three decisions that sort the range, which are the type of tap, the way it mounts and the finish, and then sends you to the collection that goes deeper on each. If you already know the room, the finish or the brand, use the links below and skip ahead.
Start with the type of tap
There are two basic designs. A mixer has one lever that sets temperature and flow, and it works with one hand. A mixer mixes the water before it leaves the spout, which reduces the risk of scalding, and setting the temperature in one movement can reduce wasted water. A three piece set uses two separate taps, one hot and one cold, with a spout between them. The separate taps allow finer control of temperature and flow, and the look is classic, but the set needs more bench space. Mixers suit most modern bathrooms and kitchens. Three piece sets suit traditional rooms and anyone who prefers the feel of two handles. See three piece bathroom taps and bathroom taps and mixers.
Taps for the basin
For the vanity basin, the main choice is a basin mixer. Bathroom basin taps also include three piece basin sets and wall mounted sets. Tall basin mixers stand higher on the bench and are the usual choice for an above counter or vessel basin, because those basins need the extra clearance. Inset and undermount basins suit standard height mixers or three piece sets, and a lower mixer reduces splashback. Basin spouts without a control are sold separately as spouts, for use with a wall control.
Taps for the bath and shower
For the bath, you choose between a wall mounted spout, a hob mounted spout on the deck of a built-in bath, and a floor mounted freestanding bath mixer that stands beside a freestanding bath. Bath fillers and shower and bath taps cover the combinations, and shower mixers control the shower. Swivel wall spouts come in 180mm and 220mm lengths, and the length matters: measure the distance from the wall to where the water should fall, because that sets the spout you need. Shower plates come in round and square, in 60mm and 80mm sizes, or with a separate back plate.
Taps for the kitchen and laundry
A standard sink mixer is the simple choice for the kitchen. A gooseneck sink mixer has a tall curved spout that pairs with a deep sink, and a pull out sink mixer draws out of the spout so you can reach the corners of the sink, rinse produce, fill pots and clean large trays. Slimline styles suit small kitchens with tight bench space. Check the clearances and the bench thickness, particularly for tall, pull out and filtered models. A pot filler mounts on the wall behind the cooktop, and filtered water taps deliver filtered water at the sink. See all kitchen taps. For the laundry, laundry taps serve the trough and washing machine sets supply the machine. Hob mixers mount on the bench or hob, and outdoor taps are made for outdoor use.
Sensor and accessible taps
A sensor basin mixer starts the water when hands are present, so children do not need to turn the tap, and it suits commercial rooms because it reduces cross-contamination. A care mixer has an extended handle for people who need assistance. See electronic sensor taps and accessible taps. Lever handles are generally easier to operate than a round or cross handle.
Choosing the handle
Handles come in two main types. A pin lever is minimalist and easy to use. A paddle handle is wider and has a more indulgent look. Cross handles belong with three piece sets and traditional rooms. A knurled handle, which has a textured grip, is one of the details to watch in 2026, along with faceted forms and ribbed knobs. Pick the handle by how you want to use it, then match the finish to it.
Mounting: decide this first
Choose the installation method first, then how easily the tap can be serviced, then the look. Tapware sorts into bench mount, wall mount, floor mount, outdoor and kitchen. Wall mounted tapware saves bench space and gives a clean look, but the plumbing is roughed in before tiling, so the decision is locked once the tiles go on. It needs a wall water inlet and exact plumbing measurements, and the typical pipe centres are 150mm for wall sets. Basin mounted taps are more forgiving and suit most standard Australian vanity setups. Wall, hob or floor mounting also changes labour and future servicing. See wall basin and bath mixer sets.
What to measure before you order
- The tap hole on the basin. Most standard Australian basin mixers need a single hole of 35mm.
- The distance between the hot and cold supply lines.
- Basin depth and rim height, so the spout clears the rim.
- Spout reach, so the water reaches the basin without splashing.
- Water pressure. Long reach and high spout taps need more pressure, and compact basin taps suit lower pressure systems better.
- For wall sets, the pipe centres, and whether the set is the trim only, a spout only or a complete set.
If you are buying the tap and the basin separately, match the tap to the basin's tap hole position and its minimum depth. See bathroom basins.
Cartridge and body
We recommend a solid brass body and a ceramic disc cartridge. A ceramic disc cartridge uses two ceramic plates to control the water, and it is smoother, holds its shut-off better over time and is less prone to dripping than older designs. Check that a local plumber can source replacement cartridges, aerators and handle parts before you buy. Stainless steel is the alternative body material, and 316 grade is the one to choose where corrosion resistance matters most, such as outdoors. See stainless steel tapware.
Lead-free tapware
The National Construction Code requires lead-free tapware at the point of installation in Australia from 1 May 2026. Clause A5G4 of the Plumbing Code in NCC 2022 Volume Three sets the limit: copper alloy plumbing products in contact with drinking water must have a weighted average lead content of no more than 0.25 percent. The rule applies to products that contact drinking water, so the kitchen tap and the basin tap are the ones to check. Check the product page for lead-free status, or ask us. See lead-free taps.
Water efficiency and flow
WELS is the Australian water efficiency label, and more stars means greater efficiency. Use the rating as a screening tool, because it does not tell you whether the tap suits your basin, your pressure or your daily use. Aerators mix air into the stream for a softer, fuller flow, and a cold start cartridge keeps hot water from firing for a quick task such as washing hands. Check the WELS information for each individual product, because the finish does not decide the rating. Check WaterMark approval as well: it affects legal installation in Australia.
Choosing a finish
Finish is the last decision, and the practical facts are simple. Chrome is the easiest to care for and the easiest to match later. Brushed finishes hide marks better than gloss, and matte black is a sharp, modern look that suits a regular wipe-down. Each finish has its own collection with its own guide:
- Chrome taps suit white tiles and classic and Hamptons rooms.
- Black taps give contrast against white basins, pale tiles and timber vanities.
- Brushed nickel tapware is a soft, warm silver that works with stone, timber and neutral palettes.
- Brushed brass taps and gold taps suit timber, warm whites and marble.
- Bronze taps suit earthy tones, organic materials and dark tiles.
- Gunmetal tapware suits dark cabinetry and concrete-look tiles.
- White tapware suits Scandinavian and minimal rooms, and matte white is a softer alternative to black against grey terrazzo and marble.
- Champagne taps are a softer, rosier alternative to full gold.
Looking after your taps
Wipe taps with a soft cloth and warm water, and add a mild non-abrasive soap if needed. Avoid harsh chemicals, abrasive cleaners and scouring pads, which scratch coatings. The most effective habit is to stop water drying on the tap, especially in hard water areas. Matte and PVD finishes need gentle wiping, and chrome can be polished now and then. In coastal and humid areas, choose brushed stainless steel, PVD coated matte black or brass, or well plated chrome. A PVD coating is a hard coating bonded to the surface, used for gunmetal, brass and nickel finishes.
Can you replace a tap yourself
The rules depend on the state. Western Australia and Victoria do not allow homeowners to replace kitchen or bathroom taps without a licensed plumber. New South Wales treats kitchen taps as part of the drinking water system, which also needs a licensed plumber. In Queensland, the unregulated jobs include changing a shower head, a tap washer or jumper valve, or a water filter cartridge. Across the states, homeowners may change a shower head or a tap washer. Do-it-yourself work can affect your insurance, some products need professional installation for their conditions to apply, and local council requirements may apply. Check your state's regulator, or use a licensed plumber. We recommend a licensed plumber in any case, so that the installation meets the rules.
Shop by brand
If you already know the brand, start with these brand and tap collections.
- Nero taps
- Meir taps
- Fienza taps
- Caroma taps
- Phoenix taps
- Dorf taps
- Greens tapware
- Clark taps
- Seima taps
- Modern National tapware
- Oliveri tapware
Matching is the reason to stay with one brand: when the basin mixer, shower, bath outlet and accessories share a finish and a maker, the finish matches more closely than across brands.
Complete the room
Choose the taps with the basin, the shower and the accessories in mind. Coordinate tapware with the shower heads, screens, basins, baths and toilets, so see bathroom accessories in the same finish once the taps are chosen.