Skip to content

Zanda Rose Adaptor Kit

0 Items

Whoops, there are none available in your area

View all products

Zanda rose adaptor kit: 65mm plates to cover a larger door hole

The Zanda rose adaptor kit is a pair of 65mm plates that fit onto the round rose of a Zanda lever handle and widen it from 55mm to 65mm. It is made for a door that has a larger hole than the standard rose can cover. It comes in passage and privacy versions and in six finishes, and it lets you fit a new handle without filling or repairing the door.

People search for it as Zanda rose adaptor kit and door lever adaptor kit. This page explains what a rose is, when you need an adaptor, how to check the door and how to fit the plates. For the wider choice, see Zanda door hardware, door hardware accessories, rose adapters, escutcheons and strike plates and interior door levers.

What a rose is

A rose is the small round plate behind a door lever. It sits flat on the door face, hides the hole that the spindle and the latch pass through, and carries the fixings. The standard Zanda rose is 55mm across. If the hole in the door is wider than the rose can cover, the edge of the hole shows, and the handle can look unfinished or sit loose. The rose adaptor fixes that by widening the plate.

What is in the kit

Feature Detail What it means
Size 65mm by 10mm plate Wider than the standard 55mm rose
Material Zinc alloy Strong and made for the Zanda handle finish
Quantity Sold as a pair One plate for each side of the door
Types Passage and privacy Match the type of handle on the door
Fitting Screws onto the existing rose No need to take the latch or the door off
Finishes Brushed nickel, matte black, graphite nickel, brass, white, ember bronze Pick the finish of the handle

Why the adaptor is needed

Doors are drilled for a handle set, and the hole can be larger than the standard rose covers. This happens when a door has been fitted with a different handle in the past, when a hole has been enlarged by a poor fit or when the old handle used a wide rose. It also happens when a renovation changes the paint, the trim or the door surface so that the old rose now looks small. A rose adaptor covers a larger hole without a repair, which saves a joiner, filler and a repaint.

Situation Result without an adaptor Result with the adaptor
The old hole is wider than the rose The hole edge shows round the plate The 65mm plate covers the edge
An enlarged hole from a past fit The handle can look off and sit loose The wider plate sits on solid door surface
A refresh of paint or trim The old rose looks small on the door A 65mm rose is in proportion
A new handle on an old door A mismatch between rose and hole A match with no repair

Measuring the door

Take the old handle off and look at the hole. Measure the width of the hole in the face of the door, and measure the area around it for paint chips or a split. The adaptor plate is 65mm across, so the hole must be small enough for the plate to cover it with a margin all round, and the door face around it must be flat. If the hole is wider than the adaptor can cover, a joiner will need to patch it. Measure the thickness of the door as well, since the handle set must fit it.

Check Why it matters
Width of the hole in the door face The 65mm plate must cover it with a margin
Flatness of the door around the hole The plate must sit flat
Door thickness The handle set must suit the door
Type of handle, passage or privacy The adaptor must match the handle

Measuring a door for a handle

Three measurements decide whether a handle set fits: the door thickness, the backset and the hole diameter. Measure the thickness of the door edge with a tape, then measure from the edge to the centre of the spindle hole, then measure the hole in the face of the door. If all three match the set, it drops into the existing preparation without drilling. If the old latch has a different backset, the lever will sit off centre on the door.

Passage or privacy

The adaptor kit is made in passage and privacy versions to match the handle it goes onto. A passage handle opens a door from both sides without a lock, and it is used on a hallway, a living room or a laundry. A privacy handle has a lock on the inside, and it is used on a bedroom or a bathroom. The adaptor changes only the size of the plate. Pick the version that matches the handle so the plate suits the privacy button or the plain rose.

Door Adaptor type Reason
Hallway, living room, laundry Passage The handle has no lock
Bedroom Privacy The handle has a lock on the inside
Bathroom or toilet Privacy The handle has a lock on the inside

Checking the handle range

The adaptor is made for Zanda lever handles that use a 55mm rose. Not every Zanda handle uses the same rose, so check the range of the handle on your door against the product page before you order. If you are unsure, take a photo of the old handle and the rose, or ask for help. The wrong adaptor will not screw on, and it is easy to avoid by checking first.

Fitting the adaptor

The adaptor screws onto the existing rose, so the job is quick. Fit the back plate onto the door as normal. Then unscrew the 55mm rose from the existing handle, and the 65mm adaptor screws on in its place. Repeat on the other side of the door. The latch and the door do not need to come off, and the lever handle stays where it is. Test the lever and, on a privacy handle, the lock, with the door open before you close it.

Step What to do What to check
1 Fit the back plate onto the door It sits flat on the door face
2 Unscrew the 55mm rose from the existing handle The rose comes off cleanly
3 Screw the 65mm adaptor on in its place The plate seats fully
4 Repeat on the other side of the door Both plates match
5 Test the lever and the lock Both turn and spring back

Choosing a finish

Finish Look Suits
Brushed nickel Soft grey metal, fine grain White doors and neutral rooms
Matte black Flat and dark Pale doors and timber
Graphite nickel Dark grey with a metallic sheen Dark doors and modern rooms
Brass Warm gold toned metal Timber doors and classic rooms
White A painted white plate White doors and plain walls
Ember bronze A warm, deep bronze tone Timber doors and warm schemes

Match the finish of the adaptor to the finish of the handle. Choose the same name, such as brushed nickel for brushed nickel, so the plate and the lever read as one piece.

Renovation and refresh jobs

The adaptor suits renovation jobs where the door and the handle are in good order and only the plate looks wrong. A new coat of paint, a new architrave or a changed wall finish can make an old small rose look out of proportion. Fitting a 65mm plate refreshes the door at the rose without replacing the handle set. It also saves the door from new drilling, and the existing handle stays in use.

When the door face is damaged

An adaptor covers a larger hole, but it cannot cover damage that runs past the plate. If the door face is split, chipped or crushed around the hole, the plate will not sit flat and the handle will wobble. Fill small chips with a timber filler, sand them flat and touch up the paint before the plate goes on. If the damage runs beyond the 65mm edge, the door needs a patch from a joiner. A flat, sound face is what lets the plate seat firmly, and a small repair before the fit is quicker than a rattling handle afterward.

Ordering for a whole house

If the old handles were fitted at the same time, many doors may share the same problem, so check several doors before you order. Count the doors that need an adaptor, and mark each as passage or privacy. One kit is a pair, so a single door takes one kit. Order the kits in the finish of the handles on those doors. Keep the doors that already have a snug rose as they are, since a wider rose on a door that does not need it only changes the look.

Door Kits needed Type
One bedroom door with a wide hole 1 kit Privacy
A hallway door with a wide hole 1 kit Passage
A bathroom door that is already fine None Not needed

If the lever feels loose afterward

A lever that moves or rattles after the plate is on usually has a loose fixing or a plate that is not fully screwed down. Check the screws that hold the back plate and the rose, and tighten them evenly. If the lever still moves, the spindle may be sitting short in the latch, and the handle set needs to be pushed together before the screws are tightened. A lever should return to the horizontal position by itself. If it droops, check that the spring in the handle is seated and that the plate is not binding on the door.

Caring for the finish

Wipe the plates with a soft damp cloth and a little mild soap, and dry them. Avoid abrasive pads, polish and strong chemicals, which can mark the finish. Wipe a brushed finish along the grain, and wipe a powder coated white plate gently so the coating is not scratched. Check the screws once a year, because a loose rose can rattle.

Before you order

Measure the hole and the door. Check the handle range and the type, passage or privacy. Choose the finish that matches the handle, and order one kit, which is a pair, for each door. Keep the old rose until the adaptor is fitted, in case a spare is needed.

Frequently Asked Questions

What is a door handle set and what does it include?

A door handle set (also called a door lever set or door furniture set) typically includes the lever handles for both sides of the door, a rose or backplate, a spindle to connect the handles, and fixing screws. Some sets also include a latch or lock mechanism. In Australia, door handles must comply with AS 4145 standards for security and durability. The Blue Space stocks door hardware from Zanda, Lockwood, and other trusted Australian brands.

What is the most popular door handle style in Australian homes?

Contemporary lever handles with a round or square rose are the most popular style in Australian homes currently. Matte black and brushed nickel are the dominant finishes in new and renovated homes. Traditional rounded lever handles in polished chrome or brushed nickel suit classic and Hamptons-style homes. Choosing a consistent handle style and finish throughout the home creates a cohesive, well-designed result.

What is the difference between a lever handle and a knob

A lever handle is operated by pressing down on an elongated arm, it is accessible for people with limited hand strength and is the most common door handle type in Australian homes. A door knob requires gripping and turning, which some users find less accessible. Under the Disability Discrimination Act, lever handles are recommended in accessible homes and are increasingly standard in new builds.

What is an entrance handle set?

An entrance handle set is a door handle set designed specifically for the front or entry door of a home. It includes a keyed cylinder lock integrated into the handle or separate lockset, providing external security. Entrance sets are available in a range of styles from contemporary to traditional and must be rated for external use, exposed to the elements, with weather-resistant finishes.

What is a dummy door handle?

A dummy handle is a non-functional door lever or knob that is decorative only, it does not operate a latch or lock. Dummy handles are used on doors that don't require a latch (such as double doors where one door is fixed, wardrobe doors that slide or swing without a latch, or decorative cabinet doors). They give the door the appearance of a complete handle set without the mechanical function.

What is a passage handle set?

A passage handle set includes two lever handles connected by a spindle that operate a latch, allowing the door to be opened from either side without a lock. Passage sets are used on internal doors where privacy is not required: hallways, living areas, home offices, and children's bedrooms. They are the most commonly used internal door handle set in Australian homes.

What handle do I need for a sliding door?

Sliding doors require a specific type of handle, typically a recessed flush pull, a finger pull, or a surface-mounted sliding door pull. Because a sliding door doesn't have a hinge pivot point, standard lever handle sets don't apply. Flush pulls sit recessed in the door surface and are ideal for cavity (pocket) sliding doors. Edge pulls are mounted on the leading edge of the door for easy gripping.

What is a privacy handle set and where is it used?

A privacy handle set includes a locking mechanism that can be engaged from inside the room, typically a simple push-button or turn-snib and can be unlocked from outside in an emergency using a small pin or coin. Privacy handles are used on bathroom, toilet, and bedroom doors where privacy is required but a keyed lock is not necessary.