Momo New Hampton Cabinet Handles Buying Guide
The New Hampton is a zinc alloy range from Momo with two cup pulls, a D handle and a round knob. It is a modern classic designed to exacting standards, with a sleek, curved design. The active pieces come in Dark Brushed Brass. The page covers what each piece measures, how a cup pull differs from a D handle and a knob, and what Dark Brushed Brass is. The page also explains how zinc alloy with an electroplated finish behaves, and how to size, fit and clean the range. For the whole brand, start at Momo cabinet handles.
The four pieces
The range has a wide cup pull on a 96mm centre, a large cup pull on a 160mm centre, a D handle on a 160mm centre and a 32mm round knob. Cup pulls have a distinctive half-moon shape and a comfortable grip, and cup pulls on drawers with classic knobs on cabinet doors give a balanced look in traditional kitchens. Cup or bin pulls suit Shaker, farmhouse and mid-century kitchens and are popular in brushed brass and antique bronze. See cup pull cabinet handles.
The pieces, measured
The wide cup pull has a 96mm fixing distance, a 123mm overall length, a width of 39mm and a projection of 23mm. The large cup pull has a 160mm fixing distance, a 185mm overall length, the same 39mm width and the same 23mm projection. The D handle has a 160mm fixing distance, a 168mm overall length, a width of 17mm and a projection of 26mm. The round knob is 32mm across and projects 36mm. The fixing distance is the gap between the two screw holes, measured from centre to centre, so the cup pulls run 27mm and 25mm longer than their holes and the D handle only 8mm.
The two 160mm pieces share a centre but differ in shape, so a cup pull and a D handle can swap into the same holes. The cup pulls are wide at 39mm and sit lower at 23mm projection, while the D handle is narrow at 17mm and stands out 26mm. Screws are not included. Screw length depends on the panel: 22mm for panels 16mm to 18mm thick, and 38mm for panels 32mm to 34mm thick. The screw must bite into the handle and stop short of the door face. The cabinet thickness is 16mm to 25mm.
When you replace a handle, measure the distance between the screw holes and match it to the fixing distance, not to the length of the old handle. A 128mm handle will not fit 160mm holes without new holes, so a New Hampton pull on a 96mm or 160mm centre only drops into holes spaced the same.
Cup pull or D handle
Both 160mm pieces fix at two points, so the choice is about grip and look. A cup pull is hooked from underneath and sits on a drawer face. A pull is gripped with three or four fingers, which makes pulls the better choice for heavy drawers and for children and older people. A D handle is a cabinet pull with a curved profile that curves away from the cabinet face and back again, comfortable to grip and easy to use on drawers and doors. The New Hampton cup pull is 39mm wide, and the D handle is a slim bar 17mm wide, so the cup pull has more than twice the face area under the fingers. The D handle stands 3mm further off the door at 26mm against 23mm, which is a small difference but one you can feel when you reach behind it. See D shaped cabinet handles.
The knob
Knobs take the fingers and a single screw and suit small doors and drawers, while pulls take the whole hand. Most cabinet knobs run roughly 25mm to 38mm across, so the 32mm New Hampton knob sits in the middle of the common range and suits a door or a small drawer. Its 36mm projection is deeper than the cup pulls, so check the clearance beside it. 32mm cabinet handles are a size people look for, and the knob is the New Hampton piece that matches. See cabinet knobs.
Zinc alloy in a handle
Zamak is a zinc-based alloy with aluminium, magnesium and copper. It is mostly die-cast, and it can be electroplated, wet-painted and chromate-conversion-coated well. The New Hampton is zinc alloy with an electroplated finish, and the grade and the plating metal are not named. A die-cast zinc handle depends on its finish for corrosion protection. Thin electroplated zinc alloy can fail within a few years in a shower splash zone. Indoors, away from direct splash, it is a normal material. See zinc alloy cabinet handles for the material in full.
Dark brushed brass
Dark Brushed Brass is a deep, dark gold with a brushed surface. Brushed brass is matte and subtle and suits minimalist or Scandinavian kitchens. Bare brass develops a patina while a lacquered finish holds the colour as made. Brushed brass is solid brass under a clear lacquer, while antique brass, gunmetal and brushed nickel are electroplated over brass, and a deep scratch shows yellow brass. The New Hampton is zinc alloy, so Dark Brushed Brass is a plated colour on a cast body and not solid brass. Whether the finish is lacquered is not stated, so avoid brass polish. See brushed brass cabinet handles.
The range also comes in Bronze, Dull Brushed Nickel, Matt Black, Matt Brass and Polished Nickel elsewhere, but the active pieces are in Dark Brushed Brass, so this page describes that finish only. People also look for bronze cup handles and black cup pull handles, which this set does not carry.
Choosing a size
Drawers 450mm to 600mm wide take 128mm to 160mm centres, and wider ones 256mm to 320mm, or two pulls. A standard door takes a 96mm to 128mm pull or a knob, and vanity drawers and doors usually take 96mm and 128mm centres. On the New Hampton, the 96mm wide cup pull suits a vanity drawer or a small door, and the 160mm pieces suit a drawer of 450mm to 600mm. The one-third rule says a pull is about a third as long as the drawer front is wide, so near 200mm for a drawer 600mm across. The 185mm large cup pull is the nearer size for that drawer, and the 168mm D handle is close. The rule is a rule of thumb and not a strict rule.
A pull or knob sits 40mm to 60mm in from the edge that opens, near the bottom corner of an upper door and the top corner of a lower door. Pulls run horizontally on drawers and vertically on doors. To test a size before you buy, tape a strip cut to the handle's length onto the cabinet and live with it for a day.
Matching the New Hampton to the door style
Contemporary and minimalist kitchens go with matte black or brushed nickel pulls, and Hamptons and coastal kitchens with D-pulls or cup pulls in brushed nickel, brushed brass or chrome. Shaker kitchens go with cup pulls, bin pulls or knobs in brushed brass, antique bronze or matte black, and heritage kitchens with antique bronze or aged brass and period knobs. The New Hampton cup pulls and knob in brushed brass sit in the Hamptons and Shaker notes. The range suits higher-end cabinetry. Gold, brass and bronze tones pair with navy, charcoal, blue or green cabinetry. Choose the handle finish after the tapware and appliance finishes are settled.
Brass on a painted door
Brass pairs with painted Shaker cabinetry and with oak, walnut, marble and natural stone. Coordinate finishes across cabinet hardware, appliance pulls and fixtures such as taps and lighting without making every piece identical. The rule for mixing is to keep a room to two metals and repeat each at least twice so it reads as a decision, with warm metals such as brass, gold and bronze working best together. The Dark Brushed Brass is the warm choice. It sits well with brass or bronze tapware, and it contrasts with cool nickel or chrome, which is a mix that works only if the cool metal is used more than once.
Replacing handles
When you swap handles, match the fixing distance. A new pull with the same distance drops into the old holes without drilling. Measure from the centre of one screw hole to the centre of the other. If the old holes are on another centre, you will need to fill them or drill new ones, and a filled hole shows unless the door is repainted. A knob needs only one hole, so swapping a pull for a knob leaves one old hole unused and the other to fill.
In a bathroom
Bathroom fittings need wiping and drying more often than those elsewhere, because steam and moisture leave marks. Bathrooms are more humid than kitchens, and solid brass, stainless steel and quality PVD are sound choices, with thin electroplated zinc alloy the one to avoid in a splash zone. A vanity door with a New Hampton knob well away from the shower is a fair use, and a handle in a splash zone is the case to avoid. The cabinets these handles fit are at bathroom vanities and furniture.
Caring for plated handles
Put the cleaner on the cloth and not on the hardware, and dry the handle straight away so water marks do not form. For coated finishes, use a soft microfibre cloth with mild soap and warm water if needed, dried promptly, and keep abrasive pads, powdered cleansers, ammonia, bleach and alcohol-based disinfectants away. A coating wears first where the hand lands, so wipe the grip area more often than the rest of the handle.
Related pages
For the full brand, see Momo cabinet handles. For other types and materials, see cabinet handles, zinc alloy cabinet handles and cabinet knobs.