Skip to content

Momo Flexa Leather Cabinet Handles

0 Items

Whoops, there are none available in your area

View all products

Momo Flexa Leather Cabinet Handles Buying Guide


A leather cabinet handle is a pull made from leather, usually with a metal part that fixes it to the door. This page holds the Flexa from Momo: a 160mm D handle and a 70mm pull, each in leather with a zinc alloy button. The leather comes in Light Tan and Dark Brown, and the button in Brass or Pewter. The sections below explain what leather is as a handle material and how it changes with age. They cover what each Flexa piece measures, how the metal buttons work, how to choose a size and how to fit a handle, since screws are not included. They end with how to look after the leather. For the whole brand, start at Momo kitchen and bathroom handles, and for handles of every maker and material, cabinet handles.

What a leather pull is

Leather pulls come in a few constructions. One is a decorative metal rod, 10mm in diameter, enclosed in Italian leather, hand-made in Germany, with a compact, slim profile for simple, modern cabinets, in black, chocolate and tan leather with aluminium, brass or copper metal. Another is solid brass and leather in two-tone pairings of bronze or gold with black, beige, green, orange, grey or blue. A third is a leather drawer pull held by a screw binding, in brown, natural and black leather, with gold or silver fixtures.

The common idea is a leather grip joined to the door by metal fittings. The Flexa combines the same two materials, leather and zinc alloy. The pull has button accents in Brass or Pewter finishes, so you can match the hardware already in the room.

The pieces, measured

The fixing distance is the gap between the two screw holes, overall length is the full length of the handle, and projection is how far it stands off the door.

  • The Momo Flexa Leather D Handle 160mm is leather and zinc alloy, 182mm long and 22mm wide, projecting 27mm, on a 160mm fixing distance.
  • The Momo Flexa Leather Pull 70mm is leather and zinc alloy, 70mm long and 22mm wide, projecting 24mm. No fixing distance is given for the 70mm pull.

Both come in Light Tan or Dark Brown leather, with a Brass or Pewter button, so each piece has four possible combinations. Screws are not included, so buy screws with the handles, and match their length to the thickness of your door. No fixing distance is given for the 70mm pull, so check the technical sheet before you plan the holes.

How leather ages

Leather is a natural material, and it changes. Natural leather develops a rich patina over time, colour and appearance can vary slightly between pieces, and natural leather darkens or fades with light exposure. Ultraviolet light and heat cause chemical damage to leather, and very dry air, below 40 per cent relative humidity, can make it desiccated. Untreated leather handles develop a patina over time, and applying wax beforehand slows the process and makes the leather more resistant to moisture and stains.

A Light Tan handle will therefore darken with handling and light, and a pair bought together may not stay identical if one sits in sun and the other in shade. That is part of the appeal of leather and not a fault. A metal handle is the better choice for a handle that stays as it is, and leather is the choice for one that develops character.

The buttons: zinc alloy in brass and pewter finishes

The metal part of the Flexa is zinc alloy. Zamac, the zinc-based alloy used for handles, is a family of alloys of zinc, aluminium, magnesium and copper, with excellent castability and long-term dimensional stability. It is a lighter alternative to brass that is durable, corrosion-resistant and able to keep a consistent finish, and die-cast zinc must have a corrosion-proof finish, plated or powder coated, because uncoated zinc corrodes. See zinc alloy cabinet handles for the material in detail.

The two button finishes let you pick the metal beside the leather. Brass is a warm, golden metal, and cool brushed nickel is a silvery grey with blue or pewter undertones, which is the kind of grey a Pewter button suggests. Dark Brown leather with a Brass button is the warmer pairing, and Light Tan with Pewter is the cooler one. If the room already has brass tapware or brass handles, the Brass button repeats it, and the rule for mixing is to keep one finish throughout. For solid brass in other handles, see solid brass cabinet handles.

The D handle and the pull

The D handle at 182mm on 160mm centres is the larger piece. The one-third rule says a pull is about one third the width of the drawer front, so a drawer about 600mm wide takes a pull of about 200mm, and the 182mm D handle is close to that figure. The 160mm centre is one of the most commonly sold, so the D handle often fits an existing pair of holes. See D shaped cabinet handles.

The 70mm pull is small. Drawers under 300mm wide take a pull of 70mm to 100mm or a 25mm knob, so the 70mm Flexa is the right length for a narrow drawer, a bedside cabinet or a small door. A 24mm projection keeps it close to the door, which is 3mm less than the D handle. See cabinet pull handles.

Where leather suits

Leather is warm, soft and quiet, and it sits comfortably beside timber. Timber is warm, tactile and quiet against painted joinery, and a leather pull suits the same joinery, with a Light Tan or Dark Brown pull on a timber drawer front repeating the warm tones. Leather's warmth offsets harder metal finishes on cabinetry, wardrobes, drawer fronts and sliding panels. Leather and brass pair with traditional kitchens, using pulls on drawers and knobs on doors, and the combination adds warmth to simple contemporary designs. See timber cabinet handles.

Leather also has limits. Avoid soaking leather in water. A handle that is splashed every day, on a kitchen sink cabinet or beside a basin, will take more wear than one on a wardrobe or a dresser. The cautious call is to use the Flexa where it will stay mostly dry, and a metal pull where it will be wet. See bathroom vanities and furniture for vanity cabinets.

Choosing a size

A widely used rule: a pull is about one third the width of the drawer front. For fronts between roughly 450mm and 700mm wide, 128mm, 160mm or 224mm centres suit, and beyond that, 256mm or 320mm centres, or two pulls, suit better. The Flexa 160mm sits in the middle of that range. Undersized pieces feel disconnected and oversized hardware dominates unnecessarily, which is a reason to use the 70mm pull only on narrow fronts.

The placement rule is simple. A pull sits 40mm to 60mm from the edge that opens, near the bottom corner of upper doors and the top corner of lower doors. Pulls sit horizontally on drawers and vertically on doors. A projection of 24mm to 27mm leaves room for the hand, but check clearance wherever two doors open close together.

Replacing handles, and fitting

If you are replacing existing handles, match the fixing distance. A new pull with the same distance goes into the old holes without drilling. Measure from the centre of one screw hole to the centre of the other, not from the edge of the handle. The Flexa D handle is 160mm, which is a common size.

Check the screws too, because screws are not included. Screw size varies by handle, so check the thread of the Flexa on the technical sheet. Screw length follows panel thickness: a 22mm screw for panels 16mm to 18mm thick, and a 38mm screw for panels 32mm to 34mm thick. A screw needs to bite into the handle's metal fitting and stop short of the door face.

Caring for leather and the button

The routine is light. Clean with diluted mild soap or unscented dish liquid, diluted at least 1:10 so that it is not sudsy, and let the leather dry fully before conditioning. Condition when the leather starts to look dry. A heavily handled handle may rarely need it because hand oils keep it supple, and once every one to two years suits occasional use. Apply a light coat of neatsfoot oil or mineral oil with a clean dry rag and buff dry, because heavy coats can impede breathability and encourage mildew growth. Conditioning usually darkens the leather slightly.

On sun and water, hot, direct sun is harder on this kind of leather than wetness and rain, and leather needs time to dry after getting wet or it may mildew. Leather is less common in wet environments without specific care guidance. Keep the handle out of strong afternoon sun where you can, and dry it if it gets wet. Ask us for the Flexa's own care instructions before you condition it.

Leather care is simple: clean with a damp cloth, avoid soaking it in water, and use an oil or conditioner to keep it supple. Ultraviolet light and heat cause chemical damage. Store spare leather pulls out of direct sunlight until use. Strong cleaners should stay off the button, because the zinc alloy under it depends on its finish for protection.

For the zinc alloy button, wipe with a soft, dry cloth, and avoid abrasive cleaners or harsh chemicals. Keep cleaner away from the leather, and apply it to the cloth and not to the hardware.

Related pages

For the full brand, see Momo kitchen and bathroom handles. For other types and materials, see cabinet handles, cabinet pull handles, zinc alloy cabinet handles and timber cabinet handles.

Frequently Asked Questions

What types of cabinet handles are available for bathroom vanities?

Bathroom vanity cabinet handles come in bar pulls, knob handles, T-bar pulls, cup pulls, and edge pulls (for handleless drawer looks). Bar pulls in lengths of 96mm, 160mm, and 256mm are among the most popular in Australian bathrooms for their clean, contemporary appearance. Knobs are a classic choice for traditional or Hamptons-style bathrooms. The Blue Space stocks handles from brands including Momo Handles and Zanda in finishes to suit every style.

What size cabinet handle do I need?

Australian handles are generally measured by "hole centres", the distance between the two screw holes, measured centre to centre. Common sizes include 96mm and 128mm for kitchens, and 160mm becoming increasingly popular in modern builds. As a general guide, the 1/3 rule works well: your handle length should be roughly one-third the width of the door or drawer. So a 600mm-wide drawer suits a handle around 160–200mm, while smaller drawers under 300mm work best with a shorter 70–100mm pull or a knob.

Should I choose cabinet handles or knobs?

Both have their place, and many homes use a mix of the two. Handles offer a larger, more comfortable grip, making them ideal for drawers and heavier daily use. Knobs are simple to install, easy to clean, and suit cabinet doors or lower-traffic areas where a subtler look is preferred. A common approach is to use handles on drawers and knobs on doors, giving your kitchen, bathroom or laundry a considered, tailored finish.

Can I use the same cabinet handles in my kitchen, bathroom and laundry?

Yes, and many homeowners do this to create a seamless, considered flow throughout the house. That said, it's important to factor in environment: bathrooms and laundries are exposed to higher humidity and moisture, so finishes like solid brass with a PVD coating, stainless steel, or quality powder-coated options will hold up better than raw or untreated materials over time.

How do I replace cabinet handles without drilling new holes?

Measure your existing hole centres by checking the distance between the centre of each screw hole, then choose a new handle with matching hole centres. If you'd like to switch to a different style or size, options like backplates, edge pulls, or handles designed to cover old holes make it possible to update your look without redrilling your cabinetry.

How do I match cabinet handle finishes with my tapware and appliances?

For a cohesive, well-designed home, cabinet handles are best chosen to complement your tapware, sink and appliance finishes. Matte black handles pair beautifully with matte black tapware for a contemporary look, while brushed nickel or brushed brass options suit warmer, Hamptons-style spaces. If your appliances are stainless steel, brushed nickel or stainless handles will tie the room together. It's worth considering your whole space, kitchen, bathroom and laundry, for a consistent finish throughout the home.