White basins buying guide
White is the most common basin colour, and it is the neutral choice that suits almost any vanity and tapware finish. This page holds white basins from Caroma, ADP, Timberline, Eight Quarters, Clark, Turner Hastings, Otti, Kaskade, Bao and Fienza. Most are ceramic, and the rest are concrete, solid surface and stone composite. They come above counter, inset, semi-recessed, under counter, wall hung and freestanding, in round, oval, rectangular, square and arch shapes. The guide below covers gloss and matte white, the materials, the basin types and how each is installed, the heights and clearances to plan for, and the tap hole, overflow and waste lines to read.
Gloss white or matte white
The difference is how the surface holds light. Gloss white reflects it and reads as bright and crisp, and matte white softens the reflection. Many models here come in both finishes, including the ADP Marilyn, Monroe and Arch Smooth, the Otti Artis and Bronte, and the Caroma Liano II, so the choice does not change the shape or the size. Matte finishes typically show fewer water spots and fingerprints than gloss. The matte surface is also the one that would show a dulled patch if it were cleaned with the wrong product, which the care section below covers. See matte white basins for the matte range, and black, grey, green and pink basins for other colours.
Materials
The material differs by basin, and the words matter. The Caroma Luna and Urbane II basins are vitreous china, and the Caroma Liano II and Tribute basins are fine fire clay, which is highly durable and more resistant to impact. The ADP, Otti and Bao basins are ceramic. Beyond ceramic, the page holds solid surface basins, which are non-porous and resistant to stains and scratches, concrete basins that are tested and sealed, and stone composite basins. The Scarabeo basins are Italian ceramic. Fireclay and ceramic are natural products, so a minor pimple, dimple or divot can occur and should be seen as part of the material. Variations of plus or minus 2% to the specifications are common and acceptable, and a bench should never be cut out without the basin on site for measuring. Some ceramic basins carry a wider tolerance of plus or minus 10mm. For the wider material guides, see ceramic, solid surface, concrete and stone basins.
People ask which material is best for a bathroom basin, and there is no single winner. What differs is the way each material is cared for and installed, so choose the one whose care you will keep up with. A glazed ceramic basin needs a soft cloth and mild detergent. A concrete basin needs its sealer protected. A solid surface basin can be repaired if it scratches, and a glazed ceramic scratch cannot.
The basin types
People also ask for the two main types of basin. In practice the types come from how the basin meets the bench or the wall, and each has its own page.
- An above counter basin sits on the benchtop, so the whole bowl shows. It does not protrude below the bench, so it keeps the storage space in the vanity, and its height means it pairs best with wall taps or a tower mixer. See above counter basins.
- An inset basin drops into a cut-out and the rim sits on the bench. See inset basins.
- A semi-recessed basin sits into the bench at the back with the front protruding, fitted into a furniture unit or work surface with the front over the counter. See semi-recessed basins.
- An under counter basin sits below the bench, so the bench edge frames the bowl. See undermount basins.
- A wall hung basin is fixed to the wall with the space beneath it open, and it needs a visible bottle trap. See wall hung basins, and small hand basins for compact sizes.
- A freestanding basin stands on the floor and is not fixed to a bench. See freestanding basins.
How each type is installed
Installation methods differ by maker, so read the instructions for your basin before the bench is cut. The common points are not to use epoxy type glues to fix a basin to the bench, to use the supplied template for the cut-out where one is supplied, and to use a licensed plumber for the water connections.
The sealant is where the methods differ. The Caroma Luna, Liano II and Urbane II basins are sealed at the underside of the rim to the bench with an acetic cured silicone. The Bao basins use a non-acidic silicone and not an acidic one. For an above counter Bao basin there are two separate jobs. The first is 20mm dots of non-acidic silicone underneath at no more than three fixing points, which hold the basin in place and still allow it to be lifted out later without damaging the benchtop. The second is a continuous bead of silicone around the outer rim where the basin meets the bench, matched to the basin colour, to keep water out of the cavity below. Wipe away excess with a soft damp cloth. Do not mix the two methods, and do not assume one maker's silicone suits another maker's basin.
For an under counter Bao basin, check the benchtop manufacturer's recommendations first. Lay the benchtop flat with the underside up, clean the underside of the sealing rim and trace the basin outline. Then run a continuous bead of approved flexible, water-tight adhesive between the cut-out edge and the line. Do not use epoxy, any other solid adhesive or acidic silicone. Leave the bench to dry face down for a minimum of 48 hours, or longer in cold weather, before it is installed. If a bench mounted mixer is fitted, leave enough room at the back or side to tighten the mixer fixing. The Caroma under counter method for marble or granite tops uses timber blocks fixed under the top with a two part epoxy and aluminium clip brackets held clear of the bowl. An under counter basin suits a stone, engineered stone or solid timber benchtop and not laminate.
A semi-recessed basin has its own fixing. The Caroma Luna semi-recessed basin is held by two tie brackets fixed to the underside of the counter top, with tie hooks anchoring the back of the basin. The basin must be sealed to the top and front section of the counter with acetic cured silicone. The minimum apron is 125mm, and local authorities have requirements for the minimum basin to wall dimensions. For granite or marble tops, two 20mm thick wooden blocks are fixed under the stone in the bracket positions with fast setting two part epoxy.
A wall hung basin needs fixing to a support beam or noggins behind the wall sheeting, which is set out before the wall is lined. The Clark wall basins show the steps. Provide suitable reinforcement behind the finished wall for the D.200 basin fixing kit at the fixing height. On a timber stud wall, position the noggins and studs at a height that suits the fasteners. Drill two 8mm holes for the fixing screws in a timber stud wall, or two 12mm holes for expansion fasteners in a masonry wall. Allow 48mm of thread to protrude from the finished wall, then mount the basin, level it and mark the lower fixing hole. Locate the basin on the screws, and fit the plastic bush, metal washer and nut to the right hand screw first, leaving the nut loose until the left side is eased on.
Sizes on this page
The sizes run from small round basins to wide wall hung and freestanding models. The Caroma Luna above counter basin is a nominal 450mm by 320mm, the Bao round is 360mm across, and the Caroma Liano II round runs from 400mm to 440mm, with its pills at 530mm and 580mm. ADP basins run from semi-inset rounds of about 355mm and 398mm to rectangles of 545mm, 550mm and 580mm. A compact basin suits a powder room or ensuite, and a larger one suits a family bathroom. Dimensions are nominal and subject to normal manufacturing variations, so check the physical basin before cutting a bench. See round, oval, rectangular, square, arch and fluted basins.
Tap holes and tapware
A basin can have no tap hole, one, or three, and the basin sets which taps are possible. Most basins here have no tap hole, so the mixer sits on the bench behind the bowl or on the wall. An above counter basin needs a wall-mounted tap or a tower basin mixer, and the mixer should sit well above the basin so the bowl can be filled to its capacity. Choose the tapware before the bench is drilled, and buy the basin, mixer, waste and bottle trap as one matched set. See basin mixers.
Overflow, plug and waste
The overflow differs by model. Most above counter basins here have no overflow, and some inset and under counter models include one, such as the ADP Eon wall hung basin and the ADP under counter ranges. Check each basin. The waste differs as well. The Caroma Luna comes with a chrome flush fitting waste and a white plug and is designed for a 40mm trap connection. The Urbane II has an integrated white ceramic pop-up waste, with brass caps in five finishes as an option. The Liano II comes with a colour matched ceramic pop-up. ADP, Bao and Kaskade basins are sold with the plug and waste separate. A ceramic basin's waste is tightened by hand only, with a foam washer sealed with neutral cure silicone. See basin wastes.
Brands on this page
See Caroma, ADP, Timberline, Clark, Turner Hastings, Otti, Kaskade, Bao and Fienza basins for each maker's full range, and bathroom vanities for the cabinets to pair with.
How to choose
- Choose the basin type for the bench or wall, and read the installation instructions for that type before the bench is cut.
- Choose gloss or matte white with the vanity and the tapware.
- Choose the material whose care you will keep up with.
- Check the size and the height against the room, the door swing and the circulation space.
- Read the tap hole, overflow and waste lines, and buy the waste with the basin where it is sold separately.
The bathroom basins page sets white beside every other colour, material and shape.